Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by aansssa

  1. aansssa

    Decarburization ..observed in hardening & Tempering

    thanks sir for ur reply.1% is acceptable from section thickness. and heat treatment done in gas fire contineouse furnace atmosphere is a big issue for reduce decarbourization. and second thing is we have tk soaking time in eace trey 25 min and wt is part 700gm is soaking more. is pc burn in...
  2. aansssa

    Decarburization ..observed in hardening & Tempering

    Hi,to all of you, Plz suggest to me how to controlled decarb in hardening tempering process. how much decarb should be.
  3. aansssa

    hardening and tempering

    hi sir, please suggest to me for reduce decarburization. actually new development item i have hard n tempered. but in final micro observed fully decarb. its socket Wt. 800gm Spec hardness 201-255 BHN
  4. aansssa

    Normalising process

    thanks for reply....
  5. aansssa

    Normalising process

    in EN8D material can i achieved plzgive the suggestion
  6. aansssa

    Normalising process

    i agree with u but we can achieve 180 bhn sir with air cooling i think
  7. aansssa

    Normalising process

    hi, dear all one i want discuss about normalising process.i know its so simple process but i want to discuss with ... actually if we use 0.40%C and 0.72%Mn and grade C40,EN8 or EN8D raw material for any part and forge then normalise its raw material hardness max 179 BHN. can u suggest how to...
  8. aansssa

    Carbon percentage checking in grade by chemical analysis

    sir would u tell me how to check c % by chemical analysis. actually i have checked incoming raw material but result not come accurate and std result also not correct. thanks atibha
  9. aansssa

    hardening and tempering

    sir hardness required 180-220 BHN after tempering and observed after hardening max 255BHN
  10. aansssa

    hardening and tempering

    that means if we done with 400-450°C than not much more effect in structure and structure not fully tempered martensite.only stress relief in this temperature for better structure should i go above 500°C tempered.and material is 35C8 grade
  11. aansssa

    hardening and tempering

    Sir plz suggest me how to down ferrite % of hardening. can i increase soaking time than effect in ferrite % and oil temp. we can same kept 50°C .
  12. aansssa

    hardening and tempering

    hi frds and sirs... sorry to come very late.. how r all of u.. anyway sir i want one simple question if i will tempered part in temperature 450°C and 400°C than what effect on structure and other properties. and can i tempered my part at this temperature what should be range of tempering...
  13. aansssa

    hardening and tempering

    hi sir, plz tell me how to fix tempering temperature for diff part and different grade becoz tempering temperature depend on as quench hardness and as quench hardness depend upon carbon percent and other alloying element. so plz tell me how to fixed temperature of tempering.
  14. aansssa

    Crack Observed during final assembly of socket

    can u tell me how to close this complain i m not under standing how to write in action plan and what we send to customer to close complain
  15. aansssa

    Crack Observed during final assembly of socket

    hi.all of u.. i have get one customer comlain regarding crack observed during assembly of socket.he told to us its raw material crack . can u told me that how to identified crack by eyes that it is raw material crack ,heat treatment or forging. can u tell me how to look like all forging ,heat...

Part and Inventory Search