Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by AhmedDeiaa

  1. AhmedDeiaa

    Consultant and design pump office required ?

    Dear Artisi (Mechanical , First, thanks for your quick reply I need to buy a design including pattern drawings , parts drawings , assembly drawings and then doing casting and machining assembly process inside my factory.
  2. AhmedDeiaa

    Consultant and design pump office required ?

    Hello , every one and good morning. One year ago ,I was employed in a company which is specialized in producing ( casting , machining , assembly ) a sewage water pump with a variant sizes reach to 500 l/sec and 60 m head. we have an old contract with a Serbian pump design office which sold us...
  3. AhmedDeiaa

    the first time to work on ANSYS

    Hi,every one i am a mechanical design engineer , i am a new user in ANSYS software , it is the first time to setup it. i do not know from where should i start ? i want to focus on structural mechanics like shafts,beams,pulleys and so one. is there any pdf book or site should i start with...
  4. AhmedDeiaa

    three pieces of sheet welded together to make a dish end , is it right ? help me

    JStephen (Mechanical) the second thread is completely different compared with the first one , the first one was about welding process in dish end the second one is about crowing the dish end not welding ...........thanks JStephen (Mechanical)
  5. AhmedDeiaa

    Need any one have an experience in dish end machining ?

    i have a circular sheet diameter = 3700 mm ,consist of three segments as illustrated in the attachments off course , i have two welding joints 1-can any one tell me is it okay to make a three welded segments dish end as illustrated in the attachments ? what are the recommended dimensions for...
  6. AhmedDeiaa

    Drilling Through Welded Joint , is it right ?

    Drilling Through Welded Joint , is it right ?
  7. AhmedDeiaa

    HV=220 of steel 37 sheet , does full annealing work and make the hardness reach to 140 ?

    HV=220 of steel 37 sheet , does full annealing work and make the hardness reach to 140 ?
  8. AhmedDeiaa

    HV=220 of steel 37 sheet , does full annealing work and make the hardness reach to 140 ?

    HV=220 of steel 37 sheet , does full annealing work and make the hardness reach to 140 ?
  9. AhmedDeiaa

    three pieces of sheet welded together to make a dish end , is it right ? help me

    please can any one tell me , what is the recommended welding procedures for forming a dish end (Head)consist of three pieces of sheet welded together with final outer diameter = 3100 mm it would be preferred if there is a standard for this .
  10. AhmedDeiaa

    can any one help me with a software in design a belt , pulleys and gears

    can any one help me with a software in design a belt , pulleys and gears ?
  11. AhmedDeiaa

    HV30=200 for steel sheet need to be dish end , does high hardness Inconsistent with forming end?

    unfortunately,i have a steel 37 sheet with HV30 = 200 (Hardness No.).(this high hardness due to wrong cold rolling). as you all know that cold working increase the hardness of metal and the material needed to be formed should contain a high amount of ductility so as to easy cold working ...
  12. AhmedDeiaa

    Need Press Machine Manual

    Thank you Don56 so much for your help , i appreciate that
  13. AhmedDeiaa

    Need Press Machine Manual

    Thank you so much Don 56 ,J Stephen for your help the machine is called.........HYDRAULIC PRESS WITH FIXED UPRIGHT + MANIPULATOR.... (SERTOM COMPANY)(made in Italy) max work piece diameter = 5000 mm max sheet thickness = 25 mm max pressure = 25 Mpa = 250 bar work piece dimensions :- material...
  14. AhmedDeiaa

    Need Press Machine Manual

    I have bought a second hand press machine (dish end crowning machine),unfortunately i do not have any manual or any data , i know totally how can i full control in the machine (i know the function of each button on the machine). so please , can any one tell me in details the steps from loading...
  15. AhmedDeiaa

    How Can i make a development for a pressure vessel dish end (head) ?

    How Can i make a development for a pressure vessel dish end (head) ?

Part and Inventory Search