Hello!
I need to analyze vessel with bolts. so I need to get pretension stresses in bolts.
I used commands for this - psmesh and sload, but they don`t work. I have read help for a lot of times.
then I decide to create a simple model, but it doesn`t work as well because of constraints.
could you...
Usually solid65 have bad convergence and requires appropriate data.
We tried to find optimal parameters for concrete and we presented our results here (in Russian)
http://cae-cube.ru/opredeleniye-optimalnykh-parametrov-rascheta-betona.html
I hope it may help you especially if you use...
Hello!
Try to use this program
ESEL,S,MAT,,№№№ (№№№ - your material number)
NSLE,S,corner
*GET,MAX_NODE,NODE,,num,max
*GET,Min_NODE,NODE,,num,min
*DIM,temp_n,ARRAY,MAX_NODE,6,1
*DO,I,Min_NODE,MAX_NODE
*GET,temp_n(I,3),node,i,bfe,temp
*ENDDO
so now you have the array with temperature, which you...
Thaks for your answers!
So I think in my case the only way is using my engineering knowledge.
Thus I don`t want to consider the wind load while I evaluate ratcheting. And I try to choose the worst direction of the wind to delete the most of cases while I evaluate protection from plastic...
Hello everybody.
I have a column vessel. It has the loads: D, P, W.
Let L and T equal 0.
So, I would like to evaluate the column according ASME BPVC VIII div2.
I use elastic-plastic analysis, so I use load combinations from table 5.5.
1) 2,4(P+D)
2) 2,1(P+D)+1,7W
As you know, W has different...
to TGS4-
OK, thanks for invitation, I will try to compare.
to MJCronin-
Here pictures:
sizes of bents
http://files.engineering.com/getfile.aspx?folder=d3a86f5d-3858-4727-ae06-e3d756d91c03&file=1.png.
a general form...
I have a pressure vessel with bent in its shell. So I want to evaluate this vessel acc. ASME BPVC VIII div.2 Part 5 in elastic-plastic method.
My way-
1) I build a geometry model of the vessel with the bent.
2) Use the appropriate procedure describing in ASME
Here I have a question-
When the...
Great!
But in Table 3-D.2M from ASME BPVC div.2 Section VIII it will be carbon steel the nearest group to determinate Ncss and Kcss? Yes?
Thank you for help!
Hello everybody.
I have steel SA-737 Gr.B
Nominal composition is C-Mn-Si-Cb. Well, I use table TM-1 from ASME BPVC Section II part d to know Moduli of Elasticity to use it in calculations.
What string shall I use? Material group A?
Thanks for advance!
"c) Why is T in only one load case although P can`t exist without T as a rule.
c) T is not temperature. See Table 5.2."
Koefficients with loads only show us whether this load dominate in this case or not (or this load absent in this case at all) and probability its appearance.
So...let we have...
c) I think the load T acts in a case when fixing the object does not allow to compensate temeperature free.
Thus, in cases where the load T is not involved, I still use temperature to find the temperature distribution to automatically take into account the desired properties of the material, and...
One more question please.
Is the pressure in global criteria of design condition of table 5.5 equal the pressure of hydrostatic conditions???
I always think that hydrostatic pressure greater.
so
"1-Global Criteria; Perform E-P analysis with 2.4*(P+Ps+D) to achieve convergence
2-Hydrostatic...
Hello!
I have some questions about temperature in pressure vessel.
Suppose that I have pressure vessel which operation (or design - it doesn`t matter) loads only P, Ps, D and T.
to evaluate the vessel I use elastic-plastic analysys acc. ASME VIII div.2 part 5.
So I should use load combinations...
SEXP command - here I tried to explain my chain of actions
http://files.engineering.com/getfile.aspx?folder=497cb5e1-677f-4a92-bc31-ba1081e293e9&file=2222.png
Unfortunately, I do not have a chance to read your paper.
So...you said that I should have fine mesh to get adequate results? I think...
I don`t know exactly, whether I can help you or not.
But here I tried to compare results in Nodes and Elements (in Russian). And this link lead to the one more similiar presentation (in English).
May be you can find answers to your question...
I would be glad if I can help!
