Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by dabiz7

  1. dabiz7

    Coordinate system disappears when rotating

    upgraded to 2020, when I place a coordinate system in my model, when I go to rotate or pan, the coordinate system disappears! Can't find a setting to stop this from happening, or might it be a graphic card thing? help
  2. dabiz7

    NX12 Assembly and Component color changing

    I select all components in my tree, right click, select Properties there is a check mark in the box under Layers called 'Specific component color' If I uncheck this box, all the components revert back to the source colors. My question, how did that box get checked?
  3. dabiz7

    NX12 Assembly and Component color changing

    NX12 Somehow, my complex assembly of a large number of parts, when I open the assembly, all y components are the same color. If you open each component individually, the component has the correct color. But when rolled up into the assembly, all the parts have the same color. Isn't there an...
  4. dabiz7

    NX 12 Drafting Model color in views

    Haven't been using NX for a while. NX 12. So I created an assembly of individual parts, each part file is surfaces that I have identified by a certain set of colors by part function. I rolled up all 8-10 part files in an assembly part file, and in this assembly part file, I over-ride the colors...
  5. dabiz7

    NX 7.5 sliding clip bar - how to turn off ???

    Thank you all for the first rate responses. I found this setting, indeed this setting is there. However, my system admin does not permit me to alter the customer defaults, therefore, I am screwed. But, indeed, this will turn off the rail. Steve
  6. dabiz7

    NX 7.5 sliding clip bar - how to turn off ???

    Going backwards to NX 7.5.... Can't remember how to turn off the sliding clip thingy that slides back and forth at the top below the taskbars. Can that be turned off in 7.5? I think I could do it in NX 8 and 10. Not sure about 7.5. If anyone know how to disable or turn it off, that would be...
  7. dabiz7

    Turning Translucency on, but wont turn off

    NX 10 In my top level assembly, I selected "Edit Object Display" and selected several parts, slid the "Translucency" bar over to 50 percent, and saved the model. Came back to the model later, decided I did not want the parts translucent, now it won't let me change the Translucency back to zero...
  8. dabiz7

    NX10 Reference geometry does not show in top level assy

    Thank you, once again, John Baker !!!!!!!! You are the best !!! Was great to hear you talk at the Cincinnati Users Group meeting recently!
  9. dabiz7

    NX10 Reference geometry does not show in top level assy

    Used NX8 some years ago, new to NX10........ I seem to recall that when you had an assembly with multiple parts open, the reference geometry (planes, Coordinate systems, etc) of the individual components could be visible and selectable to use for assigning constraints, etc. I can only see the...
  10. dabiz7

    Saving NX10 2D drawing to 2D DXF file problems

    New to NX10..used NX8 a few years ago. My problem is trying to make 2D DXF files from NX 2D drawing data. I try the Export-DWG?DXF, go through the settings, I'm pretty sure I am selecting everything to make a 2D DXF, then I create the DXF, when I try and open the DXF with eDrawings or...
  11. dabiz7

    Component part structure displayed in assembly Navigator...setting?

    New to NX10...last used NX8 a few years ago. Seems like I remember that when you have components in an assembly file, that when you look at the structure in Assembly Navigator window, you could click on the plus symbol next to the component name and the component structure would be there to...
  12. dabiz7

    NX10 pre-made title blocks for each drawing size

    New to NX 10 Do I REALLY have to make a new title block table for each drawing size template I need to make for my company? Hasn't someone made up a bunch of pre-made title block tables that I can choose from and paste into my drawing template file? Am I the only one not interested in the...
  13. dabiz7

    NX 10 Trying to flatten a part

    See attached image Application is NX 10 Mach 3 I have a solid body, 0.10 mm thick, with same width slits all around, chunk out of one end, kind of looks like a Bellville spring I wanted to use a sheet metal tool or some function in NX that would flatten this shape out on a plane so I can save...
  14. dabiz7

    SolidWorks 2014 Import settings

    In SOlidWOrks 2014, is there a way to control how SolidWorks imports various 3D CAD formats, specifically STEP files?? Why is it that SolidWorks imports STEP files as surfaces, not solid bodies? Is that a function of how the original file was saved? What I really want is to import the STEP file...
  15. dabiz7

    Why is SW 2014 taking so long to process Wrap command ???????????

    Machine: Windows 7 Pro 3.5 GHZ i& quad core 16GB ram 2GB Quaddro K2000D video card I have a simple sketch of lines, maybe 40 or 50 little lines, making 6 enclosed areas Use sketch pattern to make 10 x 2 wide pattern. Use Wrap to try and put on a simple curved extruded surface. It takes like...

Part and Inventory Search