I send a sample file now.
Regards
Note: there is a free "professional" software better than rho32: search for ipi2win.
https://files.engineering.com/getfile.aspx?folder=e018e41f-5cea-4930-a5ac-6a9801237a0c&file=rho32.dat
Saiedsadat,
I am not sure if the Standards have such probability coefficients.
More transformers, more fault current, but current to ground are no increased, because the bigger fraction of current returns via neutral to the transformers.
In some cases the neutrals of transformers can be...
Saiedsadat,
In low voltage circuit, the current to ground can't be bigger than Uphase/Rground, or Uline/sqrt(3)/Rground.
I assumed that your Uphase was 0.217 kV as the figure you sent, really is is 0.400/sqrt(3)= 231 V.
Rground is the resistance to ground of your grid1 electrode.
The SC...
Saiedsadat,
The 75 kA may be correct as fault to metallic circuit, but the current injected to ground cannot be bigger than 0.217/Rground, surely a small fraction of 75 kA.
Regards,
Gtpplot reads the .cfg file and uses timemul
I your example, timemul is
0.477225214242935
It is in micro seconds
The .dat contains:
1,0,267801390,1676682854,-1947471288,84259708,482838889,-574376845
2,349,401917008,1593459685,-1998414489,111587178,464445025,-587236013...
Bacon4life,
I am developing Gtpplot as an EMTP-ATP viewer. The program can read COMTRADE files, but I have not access to true COMTRADE files, I am retired since 1996.
Any example of such file are welcome, I can correct the reader using it as a reference.
The signal has harmonics that are not...
Tofulover,
A bit better.
The problem with the standard is that the tables are coarse, any deviation from the exact R(V) or I(t) multiply the errors.
If you try with RF > 0 (using the graphic method) the errors are bigger.
It is a case where one must have faith... and I have not faith in the...
Tofulover,
You calculated the third column of your table (Ibody) applying the BF factor
1000/775= 1290 mA but you have 1719 mA (1290/0.75)
Are you using the third column to calculate Utp?
If yes, you calculate Utp using 1/0.75 times de current.
Regards,
OPH. 2020-06-22 09:53
Tofulover,
You obtained a table of I(V) and R(I) with exact values for the table values, and a good approximation for the rest of values.
Now, you can use a table of I(t) (or t(I)) to calculate V(t), as the EN50522, with the HF, BF and Weight for each case.
The last step is to compare your...
Tofulover
The paper shows how to solve the non-linear circuit graphically.
The tables are from a old Standard, I obtained the coefficients for R(V) 50% with the table if EN50522:
There are a lot of linear (as Excel use in your figure) and non-linear fitters.
Vtouch Table EN50522...
Tofulover
To be sure about the problem of lin-lin itnetrpolation I was clear, I prepared two figures. A table of ten values of x (1...10), y=10/x.
In both cases the interpolation was done linearly, from x=1 to 10 in 0.1 steps, but the second figure was calculated with
the procedure x-->...
Tofulover
When you have not a function to calculate a value from some argument, and you have a table, you can interpolate using the table.
If you have few values in the table, the linear interpolation may work well for some cases, but if yoy want a log-log plot, you will see not rectilinear...
