Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by NikonF6

  1. NikonF6

    NX9 parts highlighting itself

    Thanks, at this moment I think the same. When I select "move object" and select object, some rendering starts over the screen and last c.2 minute.
  2. NikonF6

    NX9 parts highlighting itself

    Thanks It helps. But now when I select the part and press ESC part starts deselecting very slowly. Should I re-install ug? It just became unacceptable slow.
  3. NikonF6

    NX9 parts highlighting itself

    NX 9: whenever my cursor comes over any part in 3D- modeling, the part starts highlighting itself, line by line, and I have to wait that it is over to continue working. I just must not touch any part with cursor. How to fix it? Thanks
  4. NikonF6

    Win 7 or 8.1 for NX7.5

    Blas Thanks a lot for win10 info. I am forced to use it (at this moment) because my win7 has no driver for sky-lake cpu-usb3. All I use windows for, beside operating system, is win-explorer to copy/paste/erase files, so I am actually not interested in its capabilities. NX10: I use NX7.5 to model...
  5. NikonF6

    Win 7 or 8.1 for NX7.5

    I can run NX7.5 on win10, but some parts (commands) of menu are just not there (compared to win7) (e.g. Analysis > measure surface) and it has to be run through command finder which gives an option to include it into the menu. But after the reset it is the same. I just wonder if it is the same...
  6. NikonF6

    Win 7 or 8.1 for NX7.5

    What would be the most important differences between the two OR what be the better choice? Thanks a lot
  7. NikonF6

    FEMAP and ug-NX7.5

    Can someone comment on difference between FEMAP (latest) and ug-NX7.5, regarding FEA, with single part and assembly Linear non-linear fluid flow thermal size of the model (eg. FEAMAP can handle whole construction machine assembly, NX only "small" assemblies)
  8. NikonF6

    NX 7.5 RAM

    What is max RAM NX7.5 can use? with win-7
  9. NikonF6

    Exporting assembly level into individual component step files

    File > export > stp when selecting parts to be exported do not click at individual parts but select them all at once with rectangular system : point the cursor at upper Left corner and then drag the cursor across whole assembly.
  10. NikonF6

    NXNastran ILP solver

    are nastranw.exe, and nastranw64.exe ILP solvers in NX7.5
  11. NikonF6

    NX7.5 - LP and ILP solvers (stress analysis)

    I have Nx7.5, 16 GB memory (RAM), DeLL work station, SSD in NXNSTRAN > BIN >.. there are LP solvers, which can address max 8 GB RAM, and it works fine Nastran.exe nastran64.exe ILP solvers, which can address max 1 TB of RAM, and I can't make them works with more than 8 GB nastranw.exe...
  12. NikonF6

    NX-Nastran LP and ILP solvers

    thanks Joe There is no File > Preference, in NX7.5
  13. NikonF6

    How should I answer what is the error of my FEM calculation?

    The answer is in verifying your FEM. It is a good question how you know your result is not 200% off. Remember: any FEM MUST be verified, otherwise it is useless to anyone. Remember: FEM result is only 3% job done, rest 97 % is still engineering work... However, nowadays looks that 97% of the job...
  14. NikonF6

    NX-Nastran LP and ILP solvers

    I have Nx7.5, 16 GB memory (RAM), DeLL work station, SSD in NXNSTRAN > BIN >.. there are LP solvers, which can address max 8 GB RAM, and it works fine Nastran.exe nastran64.exe ILP solvers, which can address max 1 TB of RAM, and I can't make them works nastranw.exe nastranw64.exe I made...
  15. NikonF6

    moving icons problem

    NX 7.5 and Win-10, high resolution screen To max graphic area, I move icon by icon into graphic area and then click at X to remove the icon set which i do not need. It were all fine with Win-7. However with Win-10 , whenever I pick the icon-set (e.g standard) and try to move it into graphic...

Part and Inventory Search