Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Trevorsg80

  1. Trevorsg80

    Volume of Horizontal Cylindrical Tank at angle

    Other than very basic derivitives everything in calculus is high level to me.
  2. Trevorsg80

    Volume of Horizontal Cylindrical Tank at angle

    Hello All. Hopefully this is the best place for this question. It did not seem applicable to other forums. The question I have is I have a horizontal configured storage tank with capsule ends that is set on an angle for drainage. I need to know what the volume of this tank is at any height the...
  3. Trevorsg80

    Horizontal stoarage tank saddle shroud

    EngAddict, do you know of any manufactures? I've been looking but have not found anything yet. I'm probably not using the right search term in google.
  4. Trevorsg80

    Horizontal stoarage tank saddle shroud

    IFR and EngAddict. That was my first thought was some sort of flexible rubber skirt around it. Just was not sure what type of material and the best way to attach it.
  5. Trevorsg80

    Horizontal stoarage tank saddle shroud

    The coefficient of friction would be too high with that size of PTFE pad. As the pressure increass the friction decrease. Sounds counter intuitive but that is the explanation that I got from the engineering firm who designed the pads. Even if we did have the same size pad as saddle I would...
  6. Trevorsg80

    Horizontal stoarage tank saddle shroud

    Raising that high will still not prevent steam or water to get under the saddle plate. Also, that is not an option as the architectural design of the room will not allow it.
  7. Trevorsg80

    Storage tank saddle bearing shroud

    jtseng123, it is a horizontal tank, not a vessel technically. This will not be pressure rated or air tight. I've moved the post here >http://www.eng-tips.com/viewthread.cfm?qid=329495 as this seems more appropriate for that forum. Did not see that on the list of forums when I posted it here...
  8. Trevorsg80

    Horizontal stoarage tank saddle shroud

    My question is that I have a horizontal storage tank with one floating saddle on teflon pads. These tanks have a high cyclical load from thermal expansion so it will need to allow some flex in it. This will be in a pharmaceutical clean room with a lot of water and steam. What I need help with is...
  9. Trevorsg80

    Storage tank saddle bearing shroud

    My question is that I have a horizontal liquid storage tank with one floating saddle on teflon pads. These tanks have a high cyclical long from thermal expansion so it will need to allow some flex in it. This will be in a pharmaceutical clean room with a lot of water and steam. What I need help...
  10. Trevorsg80

    Steam venting.

    I have an application where we use hot water and steam to sanitize storage tanks. Currently the tanks are vented inside of the room but I want to use some sort of steam trap at the vent to capture the steam. Venting to outside is possible but in the summers the ambient exterior temperature can...
  11. Trevorsg80

    Simulation desgin

    Yeah, the contoact pressure is what I want. The problem I am having is that I can't get the fixtures correct. The plate is floating on the "bearings" with the load pretty much uniformily distributed. All I want is to have a uniform load of 120,000 pounds distributed onto the three bearings. I've...
  12. Trevorsg80

    Floating saddle base for water tank

    Thank you guys for all of your help on this. I think I've gotten my design and have found a supplier to make it for me. The company recommends that I have a minimum applied force of 75 psi on the pads during the expansion cycle though. Does this sound correct? Under these guidelines I will use...
  13. Trevorsg80

    Simulation desgin

    I posted this in the wrong forum so I am going to put it on here. I am trying to determine the amount of stress that is occurring to a plate that is being supported by three bearings. I am not sure if my results are coming out correctly or not. The intent is to have the bearings fixed and a...
  14. Trevorsg80

    Simulation Help

    I've also attached the assembly that if this helps you understand what I am working on.http://files.engineering.com/getfile.aspx?folder=c75d0ca9-383a-4949-8d6e-611a5874ab30&file=Bearing_Load_Study.zip
  15. Trevorsg80

    Simulation Help

    I am new to working with the simulation program in Solidworks and hoping this is the right location to ask this question. I am trying to determine the amount of stress that is occurring to a plate that is being supported by three bearings. I am not sure if my results are coming out correctly or...

Part and Inventory Search