Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by WiQi

  1. WiQi

    COLD FORMED STEEL STRUCTRUE

    HI how the cold formed steel design is different from the Hot rolled steel design? is design of cold formed steel structure on SAP2000 ok or some other software should be used? any other good software for CFS design? how do we apply temperature on the CFS structure.i have CFS model is sap2000...
  2. WiQi

    EXPORTING BASE REACTIONS at Different levels

    Hi, I have a building foundation at three levels z=3,z=-18 and z=-26.5, how do i export these base reactions as .f2k format for the foundation analysis in safe.i tried exporting them, when i put elevation level -26.5 sap gives reactions at -18 but i couldn't able to get the reactions at z=-26.5...
  3. WiQi

    Over Head Water Tank

    thanx @minochord how to apply these forces in SAP2000.
  4. WiQi

    Connection and meshing

    after analysis go to Display>Show forces/stresses>frames the pop down appears select the load combination, and direction in which you require displacement and select show values at the end, scrolling pointer will show you the displacements.
  5. WiQi

    Over Head Water Tank

    thanx @darthsoilsguy2 and @CELinOttawa ,thanx, no apologies sir in our area most of housing societies has the practice of concrete OHWT so that its concrete. i will consider the option of steel tank on RC columns.
  6. WiQi

    Over Head Water Tank

    AWWA D100 is for steel tanks
  7. WiQi

    Over Head Water Tank

    Thanx All of you for responding @JAE: i have seniors with me at my company. here i posted it to have second opinion, to have latest issues/research/problems that might encounter on the way.Also opening this question may benefit other freshers. in my company practice is to use SAP2000 , any...
  8. WiQi

    Over Head Water Tank

    Hi I have to design a OHWT of capacity 60,000 gal (imperial). shape is octagonal on six RC columns height of the base of tank is 60',dia at 60 Elev. 23',dia at 60+5 Elev. is 37' and with this dia it goes straight up for 9',top is coned with an height of 9'. soil BC is 2tsf.how to start the...
  9. WiQi

    Column Fixed support

    Hi, how to make a column have fixed support, is longitudinal bars bending pattern at foundation level effect the fixity condition, mean if bars are bent inside and if bars are bent outside or bars are not bent at all they are erected without bending what will be the difference in behavior.
  10. WiQi

    SAP2000-Frame loads

    @avscorreia: I have two versions of SAP2000 v14.2.4 Advanced and v15.0.0 Ultimate ,the above mention "Load transfer Options" couldn't be found in these two versions.
  11. WiQi

    SAP2000 MODELING PROBLEM

    @BAretired: thank you for your response id try as L beam
  12. WiQi

    COLUMN SIZE INCREASE

    @KootK: wall is there around the periphery in between columns but it is just at lower ground(basement) in upper two stories there is no wall between columns. this wall is not shear wall but basement wall which will retain the soil just.
  13. WiQi

    COLUMN SIZE INCREASE

    kindly check the link below to check columns sections http://wiki-edupunk.blogspot.com/2014/08/beams-columns-plans-and-column-sections.html
  14. WiQi

    COLUMN SIZE INCREASE

    sure, here it goes, i had problem uploading to a free space. http://wiki-edupunk.blogspot.com/2014/08/blog-post_31.html
  15. WiQi

    COLUMN SIZE INCREASE

    thanx KootK actually they have also cast a reinforced basement wall all around the columns periphery when design was revised it was failing in beam capacity ratio I suggested increasing column sizes but contractor have to do lot of chipping and drilling, and anchoring chemical so the need more...

Part and Inventory Search