Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. jamesl

    Sec.VIII-1 shell formula origin

    I think the paper by H.C. Boardman in 1943 “Formulas for the design of cylindrical and spherical shells to withstand uniform internal pressure” was the basis of the UG-27 equation. The paper started with classical equations, which had been used in Appendix 1-2 of Div 1 Code up to 2007 Edition...
  2. jamesl

    Skirt to bottom head weld

    If the skirt is not continuous welded, and bottom head is insulated, how do you prevent rain water getting into insulation? All the specs I have seen requires continuous weld at skirt attachment if the specs cover the subject
  3. jamesl

    Requirement of test coupon as per UCS 85

    I don't know why you did normalizing after cold forming. I typically see normalizing during hot forming or after hot forming. Either way, weldtek's interpretation is clear and correct. If you already have the MTR for normalized plates from the mill, you don't need to run test coupons again.
  4. jamesl

    Welding Q&T P1 Steels

    I see some confusions here between the Quench and Tempered materials covered under UHT section of the Code and regular P1 materials in Q&T condition. They are different. There are no special fabrication requirements for regular P1 materials (such as SA-105 or SA-350) in Q&T conditions. I think...
  5. jamesl

    Clad Tubesheet for High Temperature application

    If the equipment is in hydrogen service, you don't want to use carbon steel at 465 deg C. It may be OK for 465 deg F, but definitely not OK for 465 deg C. Go check API 941.
  6. jamesl

    Impact tested or normalized

    If you don't care if the plates are normalized, it is better to specify SA-516 only. Vendor can choose to buy as rolled plates with impact test or normalized plates to get away with impact test, whichever is more convenient and economical.
  7. jamesl

    Impact tested or normalized

    Order normalized will give you Curve D.
  8. jamesl

    PWHT & NDE on clad plate for wet sour service

    Of course I was talking about carbon steel vessels in wet sour service. Once the vessel is cladded, there is no need for base material chemistry control, PWHT, hardness control, etc. If we are talking about identifying defects that are related to wet sour servce, WFMT is a more effective...
  9. jamesl

    PWHT & NDE on clad plate for wet sour service

    I would like to know how full RT can prevent failure from wet sour service. If we are talking about criticality, you can apply that to any vessel, no matter it is in wet sour service or not. To me the more relevant NDE for wet sour service vessel is WFMT on all internal welds after PWHT.
  10. jamesl

    ASME Sec VIII Pressure vessel

    For B16.5 flanges, plate material can only be used for blind flanges.
  11. jamesl

    SA 516 Gr70 Tube Sheet

    You can use plate material such as SA-516 70 for tubesheet as long as client spec does not require forging only. If the tubesheet has hub, see Appendix 20 of the Code.
  12. jamesl

    L7M bolting over 2.1/2" diameter

    I agree that you may be able to stamp the bolting material as SA-320 L7M. However I am not sure you can use it on a ASME Div 1 vessel. According to UG-4(e), you can use a material outside of size /thickness limit of a material spec assumuing there is no size/thickness limit given in the stress...
  13. jamesl

    Acceptable External Nozzle Loads calculation for Pressure Vessels and Tanks

    I agree with TGS4. I think jtseng123's opinion on nozzle load analysis is little out of date. Several papers have been published by vessel engineers since 8-9 years ago to not use the sustained / thermal classifications in B31 codes on vessel nozzle load analysis. They suggested treating...
  14. jamesl

    Nozzle fatigue analysis in Div 2

    I think the vendor was misusing the Miner's rule. If the load cases are indeed acting simultaneously, what the vendor was doing would underestimate the damage. A 200 ksi alternating stress intensity would do much more damages in 100 cycles than (2) 100 ksi stress intensity acting consecutively...
  15. jamesl

    Minimum Thickness for P.V. Heads

    I don't have access to the 1966 code edition. In the old days, ASME Code did not have UW-11(a)(5)(b) requirements for seamless heads. So if the head was seamless, then E=1.0. You would need only 0.4" thick head if E=1.0.
  16. jamesl

    pressure vessel stiffening rings

    My understanding is longitudinal stiffeners does not have much use for external pressure (vacuum). Circumferencial stiffener rings are very efficient for external pressure, but not very good for bending or axial compression. Longitudinal stiffeners are mostly used in marine structure. You can...
  17. jamesl

    Hydrostatic test pressure stress

    It is common to run into a situation jtseng123 described when you use dissimilar materials on one vessel. For example, before the Code made revision in UG-99 several years ago, it was common to have bolting material for custom designed body flange limiting hydrotest pressure. Hydrotest can be a...
  18. jamesl

    MDMT PV Elite

    jtseng123, Refer to UCS-68(c) for PWHT and impact test exemption temperature reduction.
  19. jamesl

    Nozzle Reinforcement (MAWP or Design Pressure)

    How about design the nozzle reinforcements to (DP + 1 psi)? This can be easily done by increasing some weld sizes. Then tell your client that the vessel MAWP is not limited by nozzle reinforcement, but limited by their spec.
  20. jamesl

    NBIC

    It should be in para 3.4.2 of NBIC. It is the year of 1968, not 1965.

Part and Inventory Search

Back
Top