Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. aliasgere

    System Error

    Dear All When undertaking an analysis with the cap plasticity model, I get the following errors in the *msg file: ***ERROR: SYSTEM ERROR IN CAPADJ WHILE TRYING TO ADJUST THE TRANSITION SURFACE: DSCRM = -983.28 291136 4 Does anyone know what this error is caused by? I am using the...
  2. aliasgere

    Changing elasticity with soil depth using UFIELD

    Thanks. Having removed the comma, the analysis runs to completion. Not sure though if it is doing what I wanted!
  3. aliasgere

    Changing elasticity with soil depth using UFIELD

    ...C DIMENSION FIELD(NSECPT,NFIELD), TIME(2), COORDS(3), 1 TEMP(NSECPT), DTEMP(NSECPT) C FIELD(1,1)=COORDS(3) RETURN END *Elastic, dependencies=1 20000., 0.3, , 0. 5000., 0.3, , 50. *FIELD, USER, _PickedSet9 _PickedSet9 is the node set for the entire model to...
  4. aliasgere

    Changing elasticity with soil depth using UFIELD

    Hi Bartosz and Caleb I would like to vary young's modulus with depth for a 3D block of soil. I was trying to follow the recommendations on this thread but my UFIELD sub-routine is not working. Is it possible to get some help from you? Regards Aliasger
  5. aliasgere

    Soil analysis - error when varying k0 with depth

    In my offshore drained clay analysis, I have been trying to vary k0 with depth in the clay to model overconsolidation. I am using the porous elasticity and modified cam clay constitutive models. However, when I run the geostatic step, even before the input file is processed, the following error...
  6. aliasgere

    Abaqus Kinematic Coupling

    I have a 30 m long cylinder made of 3-D shell elements. I have constructed a reference point at the centre of the cylinder at the top and kinematically constrained the surface nodes to it. I have left all degrees of freedom unchecked. Have applied a displacement boundary condition at the...
  7. aliasgere

    Pile loading test

    Hi Geotech 2011, I went through your input file as I would like to simulate pile driving. Is it possible for you to please explain the steps that you have used so I can understand them and apply to my model? Regards, Aliasger
  8. aliasgere

    Kimematic Coupling

    I am modelling a 3D cylindrical shell embedded in solid elements around it. At the top of the cylinder at the centre, I have kinematically coupled the reference point to the shell surface and applied vertical load, horizontal load and a horizontal moment at the reference point, for transfer to...
  9. aliasgere

    Pile loading test

    Sorry read your earlier post about poisson's ratio.
  10. aliasgere

    Pile loading test

    Yes, geostatic stress is for the soil only. Do not include the pile. Gravity is for whole model so that's correct. Do you not have normal contact behaviour (hard contact and penalty constraint enforcement method)? What value of poisson's ratio are you using?
  11. aliasgere

    How to apply a Moment Load on a Hollow Cylinder

    Hi Rob, I tried this but during analysis it gives an error relating to the degree of freedom of the nodes that are tied. However, when I use kinematic coupling it works. Is it ok to use kinematic coupling or does it have another function? Kind regards, Aliasger
  12. aliasgere

    Pile loading test

    You need to remove the pile from the geostatic stress. Just apply geostatic stress to the soil block. Also, how have you modelled your interaction. Are you using effective stress analysis?
  13. aliasgere

    How to apply a Moment Load on a Hollow Cylinder

    Hi. I need to apply a moment load to the top of a hollow cylinder which is made of shell elements. I shall highly appreciate it if someone can give me some guidance on how I can apply this load in ABAQUS. Attached file shows what I need to do. Many thanks. Kind regards, Aliasger
  14. aliasgere

    Abaqus - Shell Section Moments SM2

    I am modelling a geotechnical problem using a 3-D cylindrical shell (S4R) in ABAQUS. I get the section moment force (SM) output but I would like some advice on how I can obtain from SM2 the resultant bending moment with depth? Your assistance will be greatly appreciated. Kind regards, Aliasger
  15. aliasgere

    Shell Elements - Extracting Bending Moments

    I have modelled, using Abaqus v6.11, a cylindrical laterally loaded pile of shell elements surrounded by a solid block of soil. Is there a way to obtain bending moments at the pile nodes using the program itself? I tried the CM output but all the values are reported to be zero. Any assistance...
  16. aliasgere

    Abaqus Problem

    Thanks!
  17. aliasgere

    Abaqus Problem

    I edited my soil set to include the soil plug and it works! Thanks for your assistance. Do you have experience in using shell elements?
  18. aliasgere

    Abaqus Problem

    I also have one material property (clay) for both soil and plug. Does this mean I do not need to define an initial stress condition for the plug even though the mesh set for my soil does not include the plug.
  19. aliasgere

    Abaqus Problem

    did u apply initial stress condition to your plug soil?
  20. aliasgere

    Abaqus Problem

    No used the same solid elements as the soil and used the same properties.

Part and Inventory Search

Back
Top