Search results for query: *

Well it was originally schedule 40. However, they installed schedule 10 and I was asked to verify the stresses at the supports for the new thickness. Schedule 10 fails and stiffening is required. B31.1 does not even show an allowable for that temperature. Is there any other source that we can...

Is it acceptable to use A53 CS pipe for a generator exhaust at approx. 1000 F or some type of alloy has to be used? Thank you

Does anyone know why the profession of Civil Engineering is called “CIVIL”. I don’t buy the argument that the British used it to describe civilian in lieu of “army” engineer. In Greek Civil is called "Politikos". "Politis" menas "Citizen" and "Politikos" politician.....

Is there a MNFR for special connectors other than Simpson Strong Tie? We have some weird connections and we like to avoid designing and fabricating special hangers & connectors. Thank you

Thanks phuduhudu If that is what we want, I dont see a problem replacing it with a double clip angle connection. I was just concerned of what will happen to the beam when the pipe starts moving. Is it going to remain vertical or it will start twisting? However, I tend to agree with...

Thanks JedClampett. The connections has been made with a thick top angle bolted to concrete with two (2) anchor bolts and not the otional side clip. However, I am planing to add a stiffener to the seat angle between the bottom concrete anchor bolts. Flexibility of the connection is not that...

I have a beam spaning between two columns 14 OC that supports two (2) pipes. The pipes move due to thermal expansion and contraction and even thought the friction has been reduced, it is still high enough to induce some torsion. The question is: Can a stiffened or unstifenned beam connection...

Will heat generated from a house fire change the structural properties of the concrete significantly enough to cause concern?

I know how you feel. I have come across the same problem on many occasions and there is not much I can do but pray that nothing will happens that will affect my work. By the way - I dont think the reports are anonymous and for a good reason. Good luck staying away from those

Is there a softaware available that can perform surge or water hammer analysis? Thank you

I have a composite tube column (fab'd from plates) that I would like to clamp down with B-B channels during the concrete placement. The clamps (ties) are not welded to the plate column. I have modeled the plate but I am having dificulty with the clamp (B-B Channels)because it is only capable of...

Is there a min/max thicknes of grout that we can place behind a wall plate supporting a cantiliver beam with relatively small loading? When does bending on the anchors becomes a problem? Thanks

Any information or link on "Jacked Piles" will be appreciated. Thank you

According to AISC 9th edition (ASD) section "I5" concrete below the top of the steel deck shall be neglected when determining section properties and in calculating "Ac" for Equation (I4-1).However, the manual is not clear about the location of the concrete NA. In other words, is the rib height...

Sometimes I also certify drawings that were prepared by a the Misc, metals detailer/draftsman. However, I do perform all the necessary checks and calculations. Most of the time teh drawings have to be revised based on my comments. Does this qualify under "direct supervision" or I am also a...

I totally agree with you regarding SAP 2000. STAAD is not what it used to be. Thanks

Thanks EddyC Do you mean the temperature at the interface between the pipe support and the supporting structure will drop down to 160 deg F and 70 degrees as you move away from that interface? Since the mass is critical does length matter? Is it true that a longer pipe support member is better...

I have a member that I like to support after some deflection takes place. Is this possible? How do I model it without imposing a load on the member? Thank you

VPL I was not looking for structural engineers. I was looking for help there because they are the ones that deal with these type of pipes and supports. But they don't and that is why I posted the question on this forum because I assumed nuclear engineers like your self do know how to support a...

Yes the pipe is insulated and we will have to penetrate the insulation and jacket. My original question to my fellow structural ladies and gentelmen was: how to determine how much heat will dissipate if the support has a certain length, diameter, and thickness (assuming it will be a pipe). If I...