Greetings,
I have a customer who is to install cast-iron pump (en-gjl-250) submerged in medium (textile effluent) with pH5. Is installing sacrificial anodes a good measure to reduce corrosion rate and enhance pump life?
Medium temp : 40deg C.
ph : 5
Be curious, and furious in your pursuit...
Greetings Everyone,
Would appreciate if you could list the fundamental difference(s) between ISO 9906:2012 Grades 3B and 2B.
I have noted the submersible pumps (sewage) are to comply with this standard.
Regards,
Arshad.
Be curious, and furious in your pursuit for answers
Greetings,
Recently, I came across a submersible sump pump with Reactor Starting Method, as opposed to Star-Delta or DOL which is mostly what we are experienced in. I've tried researching online but have found the information/explanations to be too complex.
Would appreciate your help in...
Greetings All,
Can you help me summarize/tabulate the differences between SiC and WC w.r.to the below points
1. Thermal Conductivity
2. Thermal Expansion
3. Co-efficient of Friction
4. Hardness
5. Cost?
It would be highly appreciated if you could list the differences by quoting values so...
Greetings All,
Can you help me summarize/tabulate the differences between SiC and WC w.r.to the below points
1. Thermal Conductivity
2. Thermal Expansion
3. Co-efficient of Friction
4. Hardness
5. Cost?
It would be highly appreciated if you could list the differences by quoting values so...
Hi Guys,
So there is a situation with one of my client. They require a 1-Phase Electric Dewatering Pump to be connected to and powered by a 5 kVA Electric Generator. The issue is that I have only 3-Phase Motor Pump to supply. Solutions on how to connect and run the thing is welcome.
Be...
Greetings,
I would like to know how the conventional blinds fair against Line Blind Valves. Even though Line Blind Valves provide the benefit of very quick blinding/deblinding and minimal requirement of manpower, yet I find people preferring Conventional Blinds (Spectacle Blinds) for the...
Greetings,
I was studying about Pipeline Pre-Commissioning Activities and came across Barrier Testing. Could the experts here kindly clarify WHY and HOW the barrier test is performed.
Also, could you list the logical sequence (from field experience) in which the pre-commissioning activities...
Greetings,
I came across a Wet Gad Compressor (2MCL-406 : Twin Stage, Horizontally Split, 40cm Impeller Dia. and 6 No. of Impellers). It is understood that the impeller size (width) would decrease as the compression progresses. The Compressor take suction from one end, has an intercooler, then...
Greetings,
I tried researching about compressor stalling (and consequently came across surging as well) for more information. Sadly, the explanations found were too complicated. Could you explain (such that a fresher with 9 months of experience in the refining field) what compressor stalling...
Hi Everyone,
I was preparing a presentation covering the broad classification of pumps. I was considering adding a section detailing the common issues encountered with a pump during its operation. The information available from the internet is mostly exclusive to a single category (i.e, issue...
Hi all,
Could someone kindly clarify what the intended purpose, salient features, differences and the construction w.r.to shell plate of the Bottom and Annular Plate is?
What implications does it have on the tank design?
Also, what is the Diameter-Height ratio prescribed by the norms...
Hi all,
We have used 20" 8.5mm THK API 5L X65 PSL2 Pipe for Skin Effect Heat Traced Pipeline (pipeline beyond refinery walls, and ASTM A106 Gr.B XS 20" piping inside the refinery). The design pressure of the pipeline is 45kg/cm2.
Inside the refinery, the hydrotest was done at a pressure of...
Hi Everyone,
This is my first thread/query here at eng-tips.com.
I was recently having a discussion with my manager about materials (especially SS and Duplex SS). We were talking about grades and the inherent strengths and weaknesses of different grades. I was then asked of the logical reason...
