Hi everyone
I am looking for experimental data in tensile or compression test for al2024-t3 at different temperature (100-450C) and different strain rate (1-10-100)(specially 10s-1)
I know there are some constitutive equations like johnson Cook or Zener Hollomon for estimation flow stress. but I...
Hi everyone
I am looking for experimental data in tensile or compression test for al2024-t3 at different temperature (100-450C) and different strain rate (1-10-100)(specially 10s-1)
I know there are some constitutive equations like johnson Cook or Zener Hollomon for estimation flow stress. but I...
Hi to all
have you ever seen this event? I observed it many times. when I want to simulate a rotating body which is deformable and comes into contact with another deformable-body, this problem appears. for example, when we simulate friction stir welding, during the process ( when we animate it)...
Hi to all
have you ever seen this event? I observed it many times. when I want to simulate a rotating body which is deformable and comes into contact with another deformable-body, this problem appears. for example, when we simulate friction stir welding, during the process ( when we animate it)...
Hello to all,
I am modeling a rolling ball onto the surface using ANSYS Mechanical APDL. I modeled a ball far from 1mm from the plate then I applied displacement in order to the ball comes in contact. but before the ball detects the surface I see compress stress on the plate. I used these...
Hello to all,
I am modeling a rolling ball onto the surface using ANSYS Mechanical APDL. I modeled a ball far from 1mm from the plate then I applied displacement in order to the ball comes in contact. but before the ball detects the surface I see compress stress on the plate. I used these...
Hello to all
Assume that we have two welded plates(the welding process already has been simulated ). now after cooling the plates , the new simulation or new analysis ( for example rolling) has to be done on these welded plates. accordingly residual stress and displacement should be resorted...
Hi
I have accessibility to high speed computer ( CPU=24cores and RAM=32GB). I adjusted ansys mechnical apdl product launcher as follows:
high performance computing setup-Type performance computing-used shared memory parallel(SMP)-number of processor=20
when I run the simulation and check task...
hi to all
one of the best element to simulation with ALE ( arbitrary eulerian lagrangian)capability is solid 164. this element is available at ANSYS-LSDYNA. it has three DOF (ux,uy,uz). If we want to execute couple analysis (structural and thermal) like FSW ( friction stir welding) using this...
Hello to all
I am trying to simulate FSW using ansys mechanical apdl. there is a useful sample which was provided by ANSYS. you can find it at this address: https://www.sharcnet.ca/Software/Ansys/17.0/en-us/help/ans_tec/tecfricstir.html
I executed the sample step by step (for stainless steel...
Hi to all
My question is how to use inisitate command:
Assume we have 3parts. part1=plate1 , part2=tool2, part3=tool3. If we run an analysis using part1 and part2 .afterwards we want to run subsequent analysis between the same part ( part1) and part3. is it possible we write stress and strain...
Hi to everyone
I am using ANYS mechanical apdl.I wanna run an example in ansys help about: "Rezoning Using a Generic New Mesh" at the below address
https://www.sharcnet.ca/Software/Ansys/16.2.3/en-us/help/ans_adv/Hlp_G_ADVRZSMP.html
The hlep file says that in 2d simulation since we have large...
Hi to all
I was wondering is it possible to execute two different analysis types ( first static and second transient) using RESTART ?
the problem is such a way that I have to run first load step statically (because for converging I must do Rezoning mesh and it is applicable in static...
