Hi Everyone,
A few years ago I believe someone from an ASME committee mentioned on this forum they were working on a measurement data reporting standard. I read through that draft standard that was available back then and took some mental notes. And that was that. --I didn't realize this...
Sr GDTP Y14.5-2009 Exam Review Ch-8 Part-II Sep2021
I'm in the middle of section 8, Tolerances of Profile. As you may recall, I'm working through the Y14.5 standard in preparation for upgrading my GDTP certification from the tech level to the senior level. Here is the second set of questions...
Sr GDTP Y14.5-2009 Exam Review Ch-8 Part-I Sep2021
Hi Everyone! I'm up to section 8, Tolerances of Profile. As you may recall, I'm working through the Y14.5 standard in preparation for upgrading my GDTP certification from the tech level to the senior level. Here are some questions I had from...
Sr GDTP Y14.5-2009 Exam Review Ch-7 Sep2021
Hi Everyone! I'm up to section 7, Tolerances of Location. As you may recall, I'm working through the Y14.5 standard in preparation for upgrading my GDTP certification from the tech level to the senior level. Here are some questions I had from this...
Sr GDTP Y14.5-2009 Exam Review Ch-6 Sep2021
Hi Everyone! I'm up to section 6, Tolerances of Orientation. As you may recall, I'm working through the Y14.5 standard in preparation for upgrading my GDTP certification from the tech level to the senior level. Here are some questions I had on this...
Sr GDTP Y14.5-2009 Exam Review Ch-5 Sep2021
Hi Everyone! I'm up to section 5, Tolerances of Form. As you may recall, I'm working through the Y14.5 standard in preparation for upgrading my GDTP certification from the tech level to the senior level. Here are some questions I had from this...
Sr GDTP Y14.5-2009 Exam Review Ch-4 Part-III Sep2021
Study review Part-III of III for Section 4, Datum Reference Frames. This thread covers subsections 4.21 thru to the end of the section.
Q1. 4.24.1 Datum Target Symbols. It says here: "Datum targets are designated on the drawing by means...
Sr GDTP Y14.5-2009 Exam Review Ch-4 Part-II Sep2021
Study review Part-II of III for Section 4, Datum Reference Frames. This thread covers subsections 4.12 thru 4.20.
Q1. 4.12.1 Simulation of a Single Datum Plane. Section 4.12 discusses multiple datum feature references, but I'm not...
Sr GDTP Y14.5-2009 Exam Review Ch-4 Part-I Sep2021
Alright we're on Section 4, Datum Reference Frames. I'm gonna break this Q and A into three different threads. This part covers 4.1 through 4.11.14.
Q1. 4.1-4.8 There's no subsection here simply called Datums. If we've got datum features...
Sr GDTP Y14.5-2009 Exam Review Ch-3 Sep 2021
Hi Everyone! I'm studying for my Senior GDTP Y14.5-2009 Cert Exam. I currently hold the tech level, but would like to refresh my knowledge of this subject matter through re-certification. I'm up to chapter 3! There's a couple questions I have.
Q1...
Sr GDTP Y14.5-2009 Exam Review Ch-2 Sep 2021
Hi Everyone! I'm studying for my Senior GDTP Y14.5-2009 Cert Exam. I currently hold the tech level, but would like to refresh my knowledge of this subject matter through re-certification. There's a few questions from chapter 2 that I would...
Sr GDTP Y14.5-2009 Exam Review Ch-1 Sep 2021
Hi Everyone! I'm studying for my Senior GDTP Y14.5-2009 Cert Exam. I currently hold the tech level, but would like to refresh my knowledge of this subject matter by taking the higher level exam. Maybe some forum members could quiz me on chapter...
Hi Everyone,
I'm studying for the senior level ASME Y14.5-2009 exam. (I'm a CMM technician currently certified at the Y14.5 tech level.) Is this a good place to ask study questions on GD&T? Or perhaps there is a more appropriate web forum out there that someone could recommend? I'm about...
