Respected ABAQUS Users, I have made two same cae abaqus cohesive zone model but just with a difference of surface to surface contact in one model and node to surface contact in another model gr8 and gr9 respectively in the interaction module and I got different results. Kindly solve this...
Respected ABAQUS users, I would like to request the solution to the issue regarding making the contact in cohesive zone modelling.
1. When I used the node to surface contact in the interaction by selecting node as slave and surface as master in the discretization method the output results...
Respected ABAQUS Users, I want to ask about the experimental input for the cohesive zone modelling debonding of single lap joint during the shear test. Here I have an experimental input for some cohesive debonding force displacement curve and have several questions?
1. During the cohesive zone...
Respected ABAQUS users, I am doing cohesive zone modelling in ABAQUS for which I have made the one part and at the point of contact of two surface I just have made partition to define the traction sepration contact as if the two parts are connected to each other. How can I make the surfaces at...
Respected ABAQUS Users, I am simulating cohesive zone modeling of with the input files attached here with one as a smooth surface and the other as a rough grooved surface. The output reaction force should be greater for the rough surface due to large area of contact. The model is developed using...
This file has big contact stress may be due to bending and the with the inclusion of crack tip.
How the output is processes to get the stress- displacement curve output ;how to selct element to get stress etc, of the debonding bilinear curve as the experimental input in this case is 27MPa as a...
Respected ABAQUS users, I am simulating the cohesive zone modeling by using cohesive contact rather than using cohesive elements but when I provide the initial notch or crack inside the model the mises stress goes very high as if the point of debonding is facing the extreme bending but most of...
Respected ABAQUS users, The output results of the 2d model of cohesive zone modelling of the double cantilever beam in abaqus documentation is bilinear. Is there an example of trilinear of trapezoidal output result? What parameter should be added to get trapezoidal output?
Thanks for cooperation
Respected ABAQUS users, I have tried to model cohesive zone model of two plates using some glue in ABAQUS but I am getting a high distortion node problem along with contact overclosure along with convergence issue may be due to incorrect modeling but on the youtube tuturiols I followed each and...
Respecetd ABAQUS users, How can I export the ABAQUS mesh file to ANSYS as well as the cae fileto ANSYS completely working file to perform simulation in ANSYS. Kindly tell me the file format extension to this procedure.
Thanks for cooperation
Respected ABAQUS users, I am doing 3D cohesive zone modeling for which I have attached a cae file but there is no output result generated. Assist me
Thanks for cooperationhttps://files.engineering.com/getfile.aspx?folder=9295e11b-357b-4680-9672-a7b8ce4a083b&file=czm.cae
This is the second file in continuation to the thread name ""OUTPUT RESULT ERROR"" with single laminatehttps://files.engineering.com/getfile.aspx?folder=f7126b64-3b3f-42c9-bca9-882ef10c7694&file=lam1.inp
Respecetd ABAQUS USERS, Here I am doing the simulation analysis of shear with a little difference in geometry but for the output RF, U in the direction of applied loads at given reference points but for the model with multiple 5 laminates shows extremely huge output force for the same appled...
Respected ABAQUS users, I am doing a shear testing of the model attached here for which the force-displacement response at the reference point in y-dimentions: RF2 U2 are just upto 0.045 sec while the simulation doesnt go beyond to show complete cyclic response even after the time increment to...
Respected ABAQUS Users,
I am doing cyclic displacement controlled tensile test by input of displacemetn amplitude but taking the response at the reference point for the RF3 and U3 in the direction of load is showing that the output reaction displacement is totally...
Resepected ABAQUS Users, I am performing the tensile test upto the yield point of metallic sintered joint placed betwen the chips to join them. Taking the experimental data and putting into the ABAQUS property module and proceeding towards simulation are not giving the reliable results to match...
Respected ABAQUS Users, I have running the FEM model as attached cae file in which the job is terminated just after 0.7s while the time period is set to 1s and aslo changed to 7s in both cases the job terminates at 0.7s and not running completely. What should be done to solve the problem...
Respeceted ABAQUS users, I have installed a new version of ABAQUS 2020 but I am getting the error of ""writing data in excel file failed"" during exporting the results using plugins tools the same error I was getting using version 2014. Is there any solution to this problem?
Thanks
Respecetd ABAQUS users, I have installed abaqus 2020 but when I open the abaqus app it cannot be opened and it shows the following error; IOERROR: abaqus.rpy even after starting the server. The picture is attached here.
Thanks for cooperation...
Respeceted abaqus users, I am facing a problem in getting my results being exported from abaqus to excel using plugin option. The snapshot is attached here.
Thankshttps://files.engineering.com/getfile.aspx?folder=67da8b1c-3edf-4a5b-955c-090d8b59188f&file=abaerror.JPG
