Search results for query: *

I have a PLC-5/80E/E that has a steady force LED illuminated. There are NO comms either from the DH+ or the RS232 ports. The Processor LED is steady red. I've tried leaving the power off with the battery disconnected overnight. However, the problem still exists. I took the CPU board out and...

I want to connect a P180 to a Modicon 484 CPU. Does anyone have the cable pin-outs? We need to make a cable. thanks, CTG

I have a GE Fanuc relay module IC660BR101B mounted in a terminal base with the part number IC660TBR101A. My customer says that the TBR part number should end with the same suffix as the BR part number in order for the module to work. What is the A (or B) represent. Is it just a series...

Thanks for the reply. How do I obtain a configuration floppy? CTG

I was given a T47 to test and on power up it says: Invalid configuration information - please run SETUP program. Is this the BIOS setup? It appears that the hard drive is bad, but I'm not sure yet. Is there a way to get into the BIOS and look at the boot sequence. The floppy drive works. When...

I have an Allen Bradley IMC 4100-234 4-AXIS drive controller connected to a 1391BESAA22AQB SERVO asnd connected to a 1326AB motor. I'm using a pre-engineered cable AB 4100CCAQB cable for feedback and servo control. We're using GML software Axis #0 and #1 check out fine when I do the...

Does anyone know where to get the calibration procedure for the Modicon ASB-883-200 T/C module and the 201 RTD module? thanks, CTG

Does anyone have any experience with the 1784 PKTS/A card? We're trying to establish comms with RSLinx but we cannot seem to load the correct driver. We've been in touch with AB but the drivers on the web site don't seem to work. We're using Windows 2000 Pro. for the O/S. Any help appreciated...

Need some help setting up a B883-201 RTD Module. I'm using ProWorx and a 984-780 Processor. Does anyone have the wiring diagram and the data entry and setup for the Data Watch Window? The registers are input: 30010, 30011, 30012; and output 40010, 40011, 40012. The module appears to be a...

Yeah, I could still use the diagams. I could also use the PCB jumper settings and their function. Foxboro was really no help. I talked to them but never got the info they said they were going to fax. thanks, ctg

Does anyone have the wiring diagrams for the SPEC200 analog controllers model number KIT-E27-ID-SAS-TA? I need the terminal connection diagram. thanks, CTG

I could use some help configuring a N4V2 (4 inputs, 2 outputs) analog i/o block talking to a SLC. In the past I have used a 1747SN scanner module for discrete inputs with no problems. However, with the analog block, I get good communications with the scanner and block but do not see any data in...

Anyone out there familiar with the Allen Bradley T30 industrial terminal? I'd like to know how to clear the memory. The full model number is 1784-T30G. Could also use some help locating a manual. I searched the web but came up empty. thanks, CTG

tesection We've made some progress thanks to your help. We're using the load and flag word example to write to the module. I would be interested in seeing the FB251 example. Could you send the example to bas_00@yahoo.com Thanks for all your help and to the others that responded. Your service...

Hi Nick- We've made some progress but we're hung up on the KNKT function. When entering KY 0,0 the software comes back with "Constant out of Range". If I drop the KY and enter 0,0 the software comes back with "Segment One: Invalid Address". I'm not sure what data the KNKT block is looking for...

tesection- Thanks very much for your help. It's becoming much clearer now. If I could impose on you one more time: To start STL, do you first have to have a rung in the program validated first? And how do you program the JU to Blk 251. If I can get past this, I've got it. thanks again. CTG

Is there anyone out there that could help me program STL or a function block so I can get a SIMATIC S5 115U 943 processor to output a value to the real world via a 470-LA12 analog output module? I've been struggling with this for a while but hit a brick wall. I really need someone to walk me...

Please change 'catty' to read carry. Sorry! CTG

Can anyone supply a document showing the dip-switch settings for the B875-101 analog input module? Modicon's web site does not seem to catty the info. thanks, CTG