Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: honat
  • Order by date
  1. honat

    Rigid and fully baced steel structures

    Anyone out there can tell me why would anyone design a steel frame structure as a fully rigid moment framed structure and at the same time design the same structure as a fully brace structure? That is the structure is a fully rigid moment frame and a fully braced structure. Is this supported by...
  2. honat

    ASTM specification

    What would be the correct ASTM specification for stainless Hollow Structural Section (HSS) steel as opposed to ASTM A500 GR A, B or C for carbon steel tubes?
  3. honat

    Moment of a perpendicular frame

    1- How does a bolt connection keep any part of this frame rigid? do you mean privides fixity at that connection? 2- Are we to ignore the weight of this sytem? 3- are these element rigid? 4- The easiest steps in determining the forces in yout system (ignoring the weight of), is to first assume...
  4. honat

    Torsion of flexible diaphragms

    A couple of clarification. Yes ETABS is a building structural design tool just like STAAD would be. The other concern is that you are probably ready too much into the purpose of your DIAPHRAGM. Its primary pupose is to reduce torional distortion in your structural frame system. For that reason a...
  5. honat

    AISC Suggested Steel shape bolt gages

    Does anyone have a copy of the AISC suggested steel beams gage chart that used to be in the old ASD revision (Blue book I do believe)? If so could you share it? Better yet, does anyone know where I can procure this information short of getting hold of the old ASD revision that I don't actually need?
  6. honat

    Allowable weld strength

    My Blodgett is the 1998 edition and AWS D1-1 is 1992 edition
  7. honat

    Allowable weld strength

    Could anyone clarify for me why the allowable weld stresses in TABLE 6 of Blodgett (Design of Welded Structures)are less than the AWS D1-1 prescribed 0.3x(nominal tensile strength of weld)? My own suspicion is that there is a reduction of 75% factor included. If so why?
  8. honat

    Steel Joist bottom chord extension

    OOPS. I meant Girders in a diaphragm system that see both flexural and axial loads in the analysis.
  9. honat

    Repair Method - structural column

    I would do one of two things. 1) I would detail a pedestal made from 4-L4x4 angle iron on top, 2-1/2" thick plates with holes for 4-3/4" HIT anchors on bottom and 4-HSS3x3x1/4 legs above the plates. Weld the angles of this entire assembly to the column just above the dented portion of the...
  10. honat

    Reinforce existing steel

    The way I will approach this situation is to separate the analysis in terms of total existing service DL stresses in the parent element alone. Then check the stress of the Parent plus reinforcing for mew added DL + Total structural service LL. Then combine these two answers and see if your...
  11. honat

    Steel Joist bottom chord extension

    Can one safetly use joist bottom chord extensions to provide adequate lateral bracing requirement for a beam column in a roof or a floor diaphragm? If so what is the magnitude of axial forces to provide the joist manufacturer? Is there also any code provision that deal with this situation? Which...
  12. honat

    Building drift due to WIND Pressures

    Is there a building code which specificaly addresses and specifies allowable building drift from WIND pressures, similar to the drift from Seismic or earthquake horizontal loads as stated in all the building codes? If so which code? If not what are some suggestions to tackle this issue?
  13. honat

    ASTM F1554 steel rods

    What allowable design values can one safely use for the tension capacity of a high strength ASTM F1554 grade 55 steel rod material? would it be 60% of actual yield strength or 70% of minimum specified tension strenght?
  14. honat

    Wood Shear Wall and Floor Diaphragm Design

    1)Use blocking to achive this horizontal shear transfer. You will need it anyway due to your different floor joist orienations 2)For your diaphragm chord force transfer to the vertical brace (shear walls) you could simply use skip struts between joist say every 3rd to 5th spacing depending on...
  15. honat

    Design X brace

    The main reason for tension design is economic. In AISC 5-37 B7, slenderness requirement there is a 50% difference between the compression and tension. As your brace element get longer as is the case for large bay and heigh floor requirement (industrial plant), a compression brace element will...
  16. honat

    Tie rod Turnbuckle connection

    I am doing an analysis of an existing structure that has a tension rod with a couple of Type 1 open, form 1 turnbuckle body forged in this tension member. The connection at the turnbuckle head shows no thread projection on the rod as should be expected. My question is: Is there a minimum Thread...
  17. honat

    Non load bearing tiltup concrete shear wall

    Two questions on this topic: 1) Can a Non-loadbearing concrete wall or for that matter a masonry wall be designed and used as a shear wall in conjuncture with a suporting steel frame? 2) If yes, where can I find a good design manual or software that does handle this topic?
  18. honat

    Concrete Slabs on Metal Deck governing code

    Composite concrete deck Can a girder parallel to the metal deck span be considered as composite and designed as such? How can one consider such girder as part of the shear transfer mechanism?
  19. honat

    Anchor Bolt Design

    I am looking for minimum embed and edge distance requirement for 1 1/2 inche diameter A588 threaded anchor rods used in a 24 inches thick concrete. This concrete plate is used to resist a 300 kips pipe collar trust force. I am anticipating a 1 1/4x6x6 pull out plate with these anchor bolts. Thanks

Part and Inventory Search

Back
Top