Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. jbeckhou

    Clamp for Riser Design

    If you're using a standard API hub then you can purchase the clamp. If you look at our website we can help with the clamp. Petrotrim Services, LLC www.petrotrim.com
  2. jbeckhou

    Clamp for Riser Design

    Are you using a standard API hub? Petrotrim Services, LLC www.petrotrim.com
  3. jbeckhou

    API 6A 21st edition Section 14

    All the requirements are in API-6A/Q1 Petrotrim Services, LLC www.petrotrim.com
  4. jbeckhou

    Operating a H2 type Choke Valve (API 6A)

    Hello A needle choke shouldn't be used to shut off the well. Can you share a cut view of the assy? Petrotrim Services, LLC www.petrotrim.com
  5. jbeckhou

    NON STANDARD FLANGE DESIGN AS PER ASME SEC. VIII DIVISON 1 V/s DIVISON 2

    what are you looking for? Petrotrim Services, LLC www.petrotrim.com
  6. jbeckhou

    NON STANDARD FLANGE DESIGN AS PER ASME SEC. VIII DIVISON 1 V/s DIVISON 2

    https://whatispiping.com/difference-between-asme-sec-viii-div-1-and-div-2/ Petrotrim Services, LLC www.petrotrim.com https://whatispiping.com/difference-between-asme-sec-viii-div-1-and-div-2/
  7. jbeckhou

    Wedge Gate valve drift internal diameter

    See API-6A Petrotrim Services, LLC www.petrotrim.com
  8. jbeckhou

    API 60K MATERIAL REQUIREMENTS FOR API 10000 VALVE

    Are you making a gate valve? if you make a seat or gate from 30k material using 10k PSI the parts wouldn't pass API calculations. Our gate valve uses 75k material for the bonnet, body, flange, etc, and 75k trim or higher for the valve trim. We typically use 410SS 75k for the stem, gate, and body...
  9. jbeckhou

    PSL 3G

    The original type m was intended to only seal downstream. The upstream seat pocket has a non-sealing seat assembly which allows pressure to bypass the upstream seat and equalize throughout the valve body and only seal against the downstream seat. The handwheel is used to torque down the gate...
  10. jbeckhou

    Cast spool with flanges - Unlisted material A494 CW6MC -N26625

    It's a nickel base steel, ALLOY 625, Cast N26625. I would ask the vendor making the spool for MTR's. Petrotrim Services, LLC www.petrotrim.com
  11. jbeckhou

    Suitability of SS316 + TCC for sour service

    What are you making using 316SS / TC? Petrotrim Services, LLC www.petrotrim.com
  12. jbeckhou

    API 60K MATERIAL REQUIREMENTS FOR API 10000 VALVE

    The correct material strength would come from the results of your calculations on the trim parts. Petrotrim Services, LLC www.petrotrim.com
  13. jbeckhou

    Needle Valve Cv Calculations

    Hello This is from a Cameron H2 Choke manual. https://res.cloudinary.com/engineering-com/image/upload/v1659563014/tips/manual-Cameron-H2-Choke-1_wkexow.pdfhttps://res.cloudinary.com/engineering-com/image/upload/v1659563022/tips/manual-Cameron-H2-Choke-2_ytsrcd.pdf H2 manual Petrotrim...
  14. jbeckhou

    Hydro test acceptance acc. to API 6A

    are any parts being hydro-tested made from a casting? Petrotrim Services, LLC www.petrotrim.com
  15. jbeckhou

    API 6A hardness issue

    We have used 5k equipment for 7,500 psi rated equipment in the past. We hydro tested at 1.5 W.P. I would make sure the hardness test is being done correctly and the tools are calibrated. Petrotrim Services, LLC www.petrotrim.com
  16. jbeckhou

    API 6A hardness issue

    What is the yield strength from the MTRs? What type of wellhead equipment? Petrotrim Services, LLC www.petrotrim.com
  17. jbeckhou

    RTJ INC625 hardness

    If you're using API-6A 21st Ed. see 7.5.1.5 Petrotrim Services, LLC www.petrotrim.com
  18. jbeckhou

    11"-25K Tubing Head Spool

    I would start with the dimension shown in API 6A for 20k flanges. From there use math to figure out what requires more material. I've never seen an API 25/30K flange. Petrotrim Services, LLC www.petrotrim.com
  19. jbeckhou

    API 16AR and 4130

    Hello We used N/A on all of our PQR/WPS. Petrotrim Services, LLC www.petrotrim.com
  20. jbeckhou

    Hammer Union Threads for larger size

    API uses 8-3/4"-4 2G for their 6"-1502. I've never seen a 2202 and it's not shown in API 7HU2. Petrotrim Services, LLC www.petrotrim.com

Part and Inventory Search

Back
Top