Looking for PED vessel mfgrs 3

[monk75]

We are an ASME Code shop looking for a list of possible suppliers of PED vessels. We would prefer a list of European mfgrs as this would dramatically reduce shipping charges. Doesn't seem like the EU wants any competition from US as everything is so expensive.

Any help would be greatly appreciated.

Thanks in advance.

monk75

 

[LSThill]

Hi monk75 (Industrial)

The following link has the e-mail address for contact.

http://www.asme.org/groups/materialsandstructures/ravennaitalydbray1.pdf

 

[deanc]

http://ped.eurodyn.com

Contact your AIA.

 

[weeeds]

Try: sales@fultonenterprises.com

 

[LSThill]

There is a list of approved PED Manufacture in the LOWER 48 United State. Send me a e-mail

Leonard@thill.biz

http://www.thill.biz

 

[croy2]

Monk75,

We have the capability of manufacturing PED pressure vessels (ASME U Stamp, ISO 9001: 2000, Pressure Equipment Directive 97/23/EC: Module H), and although located in Florida, our prices are usually very competitive. Please contact me and I'll see if I can help you out.

Regards,

Chris Roy

croy@microflexinc.com

 

[monk75]

I'd like to thank everyone who has responded to this post. I asked the same question on the CEN/ECN site and haven't gotten one reply.

Thanks again,

monk75

 

[GIGI72]

We are located in Italy and manufacture pressure equipment, mostly Heat Exchanger, according to PED directive, with module H and H1 with Det Norske Veritas notified body. Consider that our typical dimension are not so big (consider up to 20" diameter).
luigi.guzzi@flovex.it

 

[ggarciae]

Before PED all manufacturers in Spain were registered companies but lists are not in e-format as far as I know.
Now this register doesn't exist.
You can browse for words "depósito recipiente presión caldera calderería reactor autoclave" or look for yellow-pages lists or asociations, for example;
Companies in Catalonia

http://www.copca.com/ct/FiraVirtual2:ExportCont

Air vessels:

http://www.paginas-amarillas.es/resultados.asp?activ=aparato+de+aire+comprimido&pgpv=1&mode=simple

Metal constructors

http://www.paginas-amarillas.es/resultados.asp?activ=caldereria+de+metal&pgpv=1&mode=simple

My top ten (not all they are):
SS vessels and heat-ex for chemical industry
Aguilar y Salas, S.A.
E. Bachiller b., S.A.
SS vessels for textil industry
Argelich y Termes, S.A.
Fired tubes steam boilers
Valtec-Umisa, S.A.
Instman Field, S.A.
Moiman, S.A.
Water tubes steam boilers
Calderas Woga, S.A.
Carbon Steel for gas vessels
Calderería Egarense, S.A.
Heat-Ex for petrochemical
Compañia Española de Calderería, S.A. CECSA
Air industry
Novair, S.A.
Hope this helps


Regards from Barcelona
G. García

 

[kooler42]

Try Hebeler Corp, 2000 Military Road, Tonawanda NY 14150
716-873-9300. They have done alot of PED for GE.

 

[jez1979]

monk75,

We are a Pressure Vessel / Heat Exchanger manufacturer based in the UK. We are able to manufacture pressure vessels to the Pressure Equipment Directive (dir.97/23/EC), and are also a U-stamp shop. We manufacture a range of standard vessels aswell as bespoke one-off designs.

For further information or to place an enquiry please contact us.

j.simpson@stanref.freeserve.co.uk

Stanref International Ltd
Northern Way
Bury St Edmunds
Suffolk
IP32 6NL

+44 (0)1284 763501 (t)
+44 (0)1284 750052 (f)

 

[welding1]

Why don't you make the vessels? You don't have to be approved to make vessels to the PED. You may need the services of a notifief body to inspect them, depending on there risk category.

You can get a free copy of the PED from

http://www.dti.gov.uk/strd/ped.pdf

Regards

John

http://www.gowelding.com