Message during closed part 2

[cubalibre000]

Hi,
when I close an assembly, the message appear when I close the assembly.
Can I avoid this message ?
If the assembly contain a lot of parts....this message become very, very annoying.
I set like the image attached, but nothing, the message remain after closed and open again NX.

Thank you...

Using NX 7.0.1.7 MP3 and TC8.1

 

[JohnRBaker]

You never told us WHAT the message said.

John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

http://www.plmworld.org/museum/

To an Engineer, the glass is twice as big as it needs to be.

 

[cubalibre000]

Sorry John,
I've not upload correctly all images.

Thank you...

Using NX 7.0.1.7 MP3 and TC8.1

 

[JohnRBaker]

This has nothing to do with whether the part is read-only or not (which is what the Customer Default setting are for). It's simply informing you that you've modified a part and it's giving you the opportunity to save your changes. What exactly would you prefer that the system do in a case like this?

John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

http://www.plmworld.org/museum/

To an Engineer, the glass is twice as big as it needs to be.

 

[looslib]

I like that message because it tells you that some component of a large assembly has been changed while open in your session of NX. It then gives you the chance to determine why it may have changed and then save it, if needed. You will see that message frequently if you just upgraded to a new version of NX as all files in the old version wil be upgrade and marked as modified when opened.
I would rather be told some component has changed and have the opportunity to save my work than lose it like the CAD system I use now does. I get one question when I exit, Are you sure? How try to figure out if some component was changed and you forgot to save it.


"Wildfires are dangerous, hard to control, and economically catastrophic."

Ben Loosli

 

[cubalibre000]

The message that I attached, it's an information message.
This message exits on close assembly part that is in read-only when contained part was modified from the last saved.
On a big assembly there are lot and lot of this message and on closing I click on the mouse 150 time.
Solutions ?


Thank you...

Using NX 7.0.1.7 MP3 and TC8.1

 

[cubalibre000]

Hi looslib,
this message is not the case that you describe.
This message exit on read-only assembly with read-only part that was modified from the last assembly saving.

Thank you...

Using NX 7.0.1.7 MP3 and TC8.1

 

[JohnRBaker]

Are you using the 'Save All' option? If so try using 'Save' and if that's still too much for you, and if all you wish to do is save the Assembly, then while IT'S the Work part, select the 'Save Work Part Only' option.

John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

http://www.plmworld.org/museum/

To an Engineer, the glass is twice as big as it needs to be.

 

[cubalibre000]

The steps are :
1) Save the big assembly without message
2) Close the big assembly with the X icon
3) Messages appear for each read-only sub-assembly that as modified part after when the sub-assembly become read-only(approved).

Thank you...

Using NX 7.0.1.7 MP3 and TC8.1

 

[JohnRBaker]

I can't say how this would behave when running under Teamcenter, but when running native, no matter how many read-only parts have been modified, when I close the assembly I only have to make a SINGLE acknowledgment that; 'YES, I understand that there are modified parts which are NOT going to be saved'.

John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

http://www.plmworld.org/museum/

To an Engineer, the glass is twice as big as it needs to be.

 

[Toost]

If you instead use File - Close - Selected parts, there is an option "force close if modified" that I think will skip the warning messages.

 

[cubalibre000]

Hi,
with your suggestion I've found the solution.

Thank you a lot.

Thank you...

Using NX 7.0.1.7 MP3 and TC8.1