Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations IDS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

ASME (mechanical) Code Issues

Ishack
  • Locked
  • Question
Post weld baking / heating of P No.1 material considered PWHT as per ASME Sec IX.
Replies
4
Views
108
CWEng
CWEng
Steve.sw90
  • Locked
  • Question
Nozzle MDMT calculation (Neck pipe thickness) 1
Replies
1
Views
46
david339933
david339933
Leandro Fernandes
  • Locked
  • Question
ASME BPVC Section IX: F-Number qualification for GMAW CRO
Replies
1
Views
51
Ishack
Ishack
mechengineer
  • Locked
  • Question
Maximum Allowable Corrosion Allowance (MACA)
Replies
3
Views
101
SnTMan
SnTMan
sftyvlv1
  • Locked
  • Question
F number substitution for a WPQ
Replies
4
Views
147
sftyvlv1
sftyvlv1
ElCidCampeador
  • Locked
  • Question
Fitting SA 815 WPS32750 for ASME VIII Div.1
Replies
6
Views
88
SnTMan
SnTMan
mechengineer
  • Locked
  • Question
The governing MAWP shall be applied for the multiple loads cases analysis
Replies
3
Views
30
SnTMan
SnTMan
ElCidCampeador
  • Locked
  • Question
UG-99(b) and (c)...what a mess!
Replies
3
Views
163
david339933
david339933
Van Thanh
  • Locked
  • Question
Definition
Replies
0
Views
15
Van Thanh
Van Thanh
RBKN
  • Locked
  • Question
API 650 Flange class selection 2
2
Replies
24
Views
484
RBKN
RBKN
sushildwivedi16
  • Locked
  • Question
Impact Specimen Size ASME Sec VIII Div. 1 (Clause UG-84(c)(2)(a)) & Div. 2 (Clause 3.11.7.2 (b))
Replies
2
Views
93
Fizza453
Fizza453
ElCidCampeador
  • Locked
  • Question
Hot forming heads, PFHT necessary?
Replies
1
Views
181
david339933
david339933
ChiangJaron
  • Locked
  • Question
ASTM material
Replies
0
Views
23
ChiangJaron
ChiangJaron
Ishack
  • Locked
  • Question
Use of in line weld test tool (IWT tool) for pressure testing of joint fulfills ASME B 31.3?
Replies
13
Views
87
DekDee
DekDee
timsch
  • Locked
  • Question
SECTION VIII, DIV.1 - Cap size larger than 4" NPS; what are my spec options?
Replies
2
Views
27
timsch
timsch
samvanwesen
  • Locked
  • Question
ASME B16.5 flange issue
Replies
3
Views
84
timsch
timsch
marty007
  • Locked
  • Question
ASME VIII-1 / NBIC Part 3 - Design Responsibility
Replies
1
Views
109
Geoff13
Geoff13
PipingMech99
  • Locked
  • Question
allowable stress values for ASTM A707 L3
Replies
2
Views
29
PipingMech99
PipingMech99
patchlam
  • Locked
  • Question
SA-234 WP11, Class 2 not in ASME II D
Replies
1
Views
31
XL83NL
XL83NL
Menon5230
  • Locked
  • Question
Welding of 1.5" Weldolet
Replies
1
Views
54
david339933
david339933
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom