Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by DesEngineer4

  1. DesEngineer4

    STEP file conversion

    Hi, I'm working on exporting a large assembly to STEP file in Solidworks 2022. Unfortunately, SW is unable to process it. We are trying to make some assemblies Virtual and tried again, still it taking days to convert to STEP file. Any other easiest ways to do it? Please suggest. Thanks & Regards
  2. DesEngineer4

    ATA 26

    That was too deep. But I got your answers. Thank You Sparweb! Thanks & Regards
  3. DesEngineer4

    ATA 26

    Hi I'm from CA Maybe I didn't put my question properly. 1- How can we determine which location is needed for smoke detection and where the detector should be installed. 2- How do we choose which kind of smoke detector to install in a corridor, bedroom, cabin, or restroom? Does it depend on how...
  4. DesEngineer4

    ATA 26

    Hello, I am working on smoke deduction routing for an Aircraft Interior. Could anyone please help in understanding about Sniffer Ports like, i) I have an input saying to use 4 sniffer ports but are there any parameters to select no of sniffer ports required per sqft? ii) We have an input which...
  5. DesEngineer4

    Irregular Profile in NX

    Hi, It need to be created with parametric features and I'm not allowed to use synchronous modelling. Also, I should try my best to not to use surfacing Thanks & Regards
  6. DesEngineer4

    Irregular Profile in NX

    Hello everyone, Wish you all a Merry Christmas! I'm writing this thread to seek your help/suggestions. I'm trying to convert one body into parametric in NX. This body has a strange irregular profile. Could you please help me or give me some suggestions on how I can achieve the shape? or how my...
  7. DesEngineer4

    Need Critical Help on Helix Cut

    Hello, Even after increasing the pitch, I'm unable to match the profile. My thread requirements Major Dia 59.53 Minor Dia 51. 05 Pitch 5.08 Thread length: 15.24 Angle; 60 Can someone please help? I tried nearly 10 iterations still failed Thanks & Regards
  8. DesEngineer4

    Need Critical Help on Helix Cut

    I have observed one more issue, the helix I have added is 3 turns, first 2 turns were matching with dumb solid but 3rd turn is not matching.. Any idea? Thanks & Regards
  9. DesEngineer4

    Need Critical Help on Helix Cut

    Hi Cowski, I tried as per suggestion, but it is not subtracting the material. I tried with Boolean operations as well. Thanks & Regards
  10. DesEngineer4

    Need Critical Help on Helix Cut

    Hello, I need some critical help on Helix Cut in UG NX 11. I'm converting one dumb solid to Parametric part. I didn't understand where I went wrong in making a Helix cut, I have added helix and Thread triangle. I have tried couple of times but failed. Could anyone help me on this? I have...
  11. DesEngineer4

    Detailing Check List

    Hello All, I'm preparing a checklist that should comply with ASME 14.100 Drafting standards. Does anyone has reference for check list? That would help drafters to reduce the errors before submitting to delivery. Could anyone help on this? Thank you for your time and support Thanks & Regards
  12. DesEngineer4

    Autovue_Drawing Compare

    Hi Dave, Somehow convinced them for GIMP in our official system, they will install in couple of days. Can we achieve the similar comparison outcome from GIMP? Thanks & Regards
  13. DesEngineer4

    Autovue_Drawing Compare

    Hi Dave, Thank you for detailed explanation, photshop is working good in my personal computer but unable to install in my office PC due to IT restrictions. Is there anyway to simply create a small software or tool only for this purpose? Thanks & Regards
  14. DesEngineer4

    Autovue_Drawing Compare

    Hello, Is there any open source software like Autovue to compare engineering drawings? The comparison result should show in colors what is deleted and what is added. Please suggest. Thanks & Regards
  15. DesEngineer4

    Manufacturing Process

    Here are the Images. Thanks & Regards https://files.engineering.com/getfile.aspx?folder=bd0b31e2-8566-48b2-9fb2-61cb92373c98&file=Engine_Bay-1.zip
See more

Part and Inventory Search

Back
Top