Thanks for the responses.
I should have also said that I've got decent competence with MIG, but not certification, and still a little weak on 6G.
Clarification - for out of position (say, 5G or 6G), I don't think spray is viable, unless you have a special CV machine that can pulse. Spray is...
I am trying to improve my welding skill set. I am D1.1 certified in stick ("SMAW") 3G 3/4" max thick plate.
1. Assuming AWS and ASME pipe welding - say 0.2" up to 0.5" wall, out of position, short circuit GMAW-S, both shop and field
My question: Is MIG with A75/C25 common and/or...
Okay, cut me some slack. Yes, the bend radius is non-uniform. I'm practicing for the test, and bent those coupons in my garage with my own $17 home-made bender. But zero cracks, guys.
So much for getting an "attaboy" from the group. Tough crowd.
Following up.
My welds are similar, but focused on code-level coupon preparation, and better wrap-bending (wheels with bearings; still a bit imperfect).
Also, minimized "time at temperature" per Armao, so just a single CJP per test mockup.
No cracks at face bend or backside bend for 2" diameter...
Thanks for the responses.
Here's my take-aways for the next set of coupons
1. No preheat.
2. Low interpass temperature - allow cooling between passes.
3. Grind edges of coupon before bending (like D1.2 allows).
4. Grind weld flat before bending.
5. Tight stringers, no weaving (I already always...
Amateur question. I have been bending my practice weld coupons around a small pipe, then bending tighter in a vice - just to check ductility.
Photos below are pre-bend and post-bend
Background:
Uphill, 3G
One-sided complete joint pen at butt joint (no gap)
6061, 1/8" thick
3/32" 5356 filler...
gtaw -
Thanks for the response.
I've been welding aluminum TIG for a little while, so I appreciate your comment about aluminum not being like steel. Very true.
Circling back on one question from my original post, which was too long.
If I test on a 3/16" thick plate (which would give me...
I am trying to get certified in TIG aluminum 6061 3G per D1.2 4043, up to 3/8" or 1/4" thick plate, and I am looking for guidance. I am trying to diversify my credentials for more job options.
[I am a steel guy and am certified 3G D1.1. Not ASME. Almost everyone I know is a steel guy. Aluminum...
3DDave and itsmoked: Thanks for the comments, even with the snickering.
I've mounted my accelerometer right next to my board with jumper wires about 4". Noise is significantly reduced to the equivalent of about 0.02g (which is good enough for my application of -1.0 to 1.0g range).
Rookie...
IR - I appreciate your sentiment to keep this forum serious and professional.
This is actually serious and professional.
The bike crank in my garage was my attempt at trouble-shooting. To be clear, this is not about bike cranks but instead structural instrumentation on a shake table.
Attached...
I ran a desktop study. Excel plot attached.
Little noise when sitting still.
Much noise with even very small movement.
1. do I have the wrong accelerometer? It costs about $20 thru Adafruit. I can spend $7 or $100 on an accelerometer. Not sure how to differentiate based on data sheets. All...
Hello my EE friends,
First, I'm sorry for the amateur question. Second, I'm hoping this is the correct forum, since double posting is a grievous sin.
I set up what I thought was plain vanilla instrumentation to measure and record structural vibrations.
Teensy 4.1 (with simple Arduino code) and...
Real useful info. Thank you all.
Yes, my driver can send up to pulses per second (0.18 deg / pulse).
However, that means that now that the max pulse rate = 94,000 pulses / second --> 10 microseconds per pulse.
I'm completely unanchored here, but that seems high.
But I will re-visit with several...
