Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jingansong

  1. jingansong

    How to make this transition mesh in Abaqus

    Hi everyone, I'm trying to create transition mesh like this in the picture, (please see the picture through the following link) http://files.engineering.com/getfile.aspx?folder=22951696-9563-409f-97dc-ae98a2222a0c&file=Transition_mesh.PNG I have used sweep mesh and transition mesh for the...
  2. jingansong

    Units

    Hi DanStro, Thank you for helping. Do you mean the force unit is still N? But I think the unit for force is kg*nm/s^2 = 10^-9 N now, so stress unit is 10^-9 N/(nm^2) = 10^9 Pa = GPa, isn't it?
  3. jingansong

    Units

    Dear all, In my model I choose the units based on "kg--mass, nm--length, s--time", so other units are density--kg/nm^3 stress--GPa conductivity--"10^-18 W/nm K" specific heat--"10^-18 J/kg K" Are these consistent? Thank you!
  4. jingansong

    Contact between a rigid body and a deformable plate

    I've followed the suggestion after this warning message to change the kinematic contact to the penalty contact, this warning is gone, and no error happened, but the weird mesh change thing is still there. I believe this is not correct. But I don't know what causes this.
  5. jingansong

    Contact between a rigid body and a deformable plate

    Here are the two captures. Thanks!https://www.dropbox.com/s/1soa13m53ivor8s/original%20mesh.PNG https://www.dropbox.com/s/w5bm2y6p6lesnb3/mesh%20after%20simulation.PNG
  6. jingansong

    Contact between a rigid body and a deformable plate

    I created a rigid body and a deformable plate. I fixed the rigid body and applied velocity on the deformable plate. A dynamic temp-disp explicit step was used for the simulation. In the contact property I specified friction coefficient and heat generation. And I used contact pair interaction...
  7. jingansong

    Contact between a rigid body and a deformable plate

    Hi everyone, I'm trying to do a contact simulation between a rigid body and a deformable plate. I used contact pair interaction. The job failed in the middle. I checked the .odb file, the plate didn't deform a lot, while the mesh changed a lot (I'm not sure if it's correct to describe it like...
  8. jingansong

    Frictional heat generation

    sdebock, Thank you, I also saw that before. Maybe I missed some tricks.
  9. jingansong

    Frictional heat generation

    Hi everyone, I'm trying to analyze frictional heat generation between two surfaces. I realized that if I use general contact, there is no temperature change at all, but if I use contact pair, there is temperature change. Is frictional heat generation simulation only possible with contact pair...
  10. jingansong

    nano scale structure contact

    IceBreakerSours, I'm doing a simulation that a sphere is sliding on a plate while penetrating to it. The plate is moving on the sliding direction, and the sphere is moving on the penetration direction, so I specified these two perpendicular velocities on them, respectively. The units for the...
  11. jingansong

    Nodes temperature in INP file

    Hi Stancler, Have you figured out your problem? I have a similar problem, if you can give me some information, it'll be very helpful.
  12. jingansong

    nano scale structure contact

    Hi IceBreakerSours, The warning message that the mass of xxx is less than xxx, is the one I haven't seen before. I checked the units, it should be correct because I used it in the micro scale simulation.
  13. jingansong

    nano scale structure contact

    Hi everyone, Is abaqus available for simulation of nano scale structure contact? I did run micro scale structure contact successfully, but when I created the geometry at 10^-3 scale level of the previous one, and kept the units system the same (so it is supposed to be nano scale), I saw a...
  14. jingansong

    excessively distortion and too large simulation time

    Hi IceBreakerSours. There are some warnings related to output request. And one warning is "Some nodes in the general contact domain are part of a sliding or eulerian boundary region. These nodes will be made lagrangian". But I saw this one before in previous simulations, I don't think this is...
  15. jingansong

    excessively distortion and too large simulation time

    Thank you IceBreakerSours. Do you mean adaptive mesh? I did use adaptive mesh in the simulation.

Part and Inventory Search