That did the trick, thanks - I used IDEAL and STEAM-TA for the water properties, apparently the steam tables use the wrong properties, which is very very confusing, changing to IAPWS-95 solved it.
Thanks!
Hi,
I have this annoying problem I'm unable to solve. When I add Water as a component in Aspen (CAS 7732-18-5) and run a Pure-property analysis, the Cp (specific heat capacity) is well off.
Where it should be around 4.2 from 0 to 100 degC, its going from 4.0 to 4.5.
I used different property...
Hi George,
Somehow I managed to upload something completely different - indeed, that is not what I wanted to share. See attached file for the right calculation - stagnant pipe with (in this case) water.
Indeed, the temperature I'm searching for is not Ti (Tinside or bulk) but T1, the wall...
Hi George,
Thanks for the Perry equation, probably more reliable than my estimation. Calculating the different T's isn't the problem. Finding the thermal resistance for the insulation also not.
The problem I have is finding the right equation. Everywhere I find the equation Q = U * A * dT...
Hi Pierre, it works, thanks! Do you happen to have access to the spreadsheet too?
Cheresources is a website I didn't knew yet, very helpfull, thanks!
Best regards,
Luuk
Hi Pierre,
Thanks, but the link doesnt seem to be working at the moment. Could you check on your side or upload it again?
Again, thanks for your help!
Hi George,
Ofcourse. This is the background; it is regarding a plant in India, we have acquired it and we want to bring it to our own company...
Hi,
I have the following problem;
We have certain big lines (DN100 till DN250) that are not fire protected (they are insulated but not fire proof). When a fire occurs and the fluid is heated up to 100 degrees Celcius, a chemical reaction could (theoretically) take place. During the fire it is...
Hi,
Thanks, this converter only is applicable for liquids as far as I can tell. Still usefull though.
I need a converter for Gas (crit/non-crit) and Steam (crit/non-crit), there are some Gas equations to be found, but no Steam correlations.
But it should be simple math, a converter does...
Hi,
I'm having some trouble converting a Cv (imperial) formula to a formula that can be used for Kv (metric).
It concerns a Cv calculation for a gas flow trough a control valve. The formula is:
Cv = [Qg * (SpGrg * T)^0.5] / [1360 * ([P1 - P2]*P2)]
This is for sub critical flow.
Cv = capacity...
Basically the new standard (7th edition) takes the calculated relief amount (f.e. 200 m3/h of Ethanol vapor at 40 degrees and 2 barg) and converts it to Nm3/h air.
However, in Annex A of the 7th edition, the alternative method of Table 1B is also displayed (the old 5th edition way).
So you can...
Thanks! I had the same interpretation. However, someone showed me the new API-2000 7th edition, and there Table 1B is removed. Instead they use a calculation method that indeed does convert to Nm3/h. This only applies if the temperature is above 49 degrees though.
So I guess the new standard...
Thanks!
No - the relief pressure at the inlet of the relief valve is not 4.706 bara, but 4.643 bara. See left upper corner - this is the Set Pressure (3 barg) + accumulation (21% = 0.63 bar) + P_atm (1.013 bar) + superimposed backpressure (0 bar) = 3 + 0.63 + 1.013 + 0 = 4.643 bar(a). This is...
Hi,
I have a question regarding the calculation of the required capacity for a Low-Pressure storage tank, using API-2000.
I'm using the 5th edition of API-2000, we don't have the newer ones available.
The case is that 100 m3/h liquid ethanol is pumped into an ethanol storage tank, displacing...
Exactly! And I'm quite sure the program does this the incorrect way. Let me elaborate, as seen in the attachment (picture) P2c (the pressure at the inlet of the relief valve in the excel sheet) is calculated by adding up the relief pressure + the pressure drop over the outlet.
But this is, as...
