Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations SDETERS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by midris

  1. midris

    PVC wrapping effect on cathodic protection shielding

    Hello, STOPAQ PVC outerwrap is being considered for aeging underground CS piping which is protected by an impressed current CP system. The current drain test was performed on the piping and the required current for protection has been determined. Will the PVC wrap result in CP current...
  2. midris

    PVC wrapping effect on cathodic protection shielding

    Hello, Stopaq PVC outerwrap has been considered for underground CS piping which is to be cathodically protected. Will the PVC wrapping result in CP current shielding? Thanks,
  3. midris

    Cathodic protection of in plant piping

    I would also like to add that I have considered the option of replacing the impressed current distributed close system of MMO canister anodes with MMO ribbon anode but the deterring factor is the very large scope of UG piping which is around 2 kilometers in length in total and I was thrown off...
  4. midris

    Cathodic protection of in plant piping

    Hello all, A requirement has been raised in the operating company I work at for impressed current cathodic protection of buried carbon steel piping which has begun to corrode rapidly in recent years. The FEED study has been awarded to an EPC contractor for proposing the most suitable impressed...
  5. midris

    Suitability of stainless steel in offshore applications

    TVP, thank you for your input, however, I have not specified that the stainless steel is used for seawater or produced water applications, in which case 60 degC would be too high even for SDSS. I would like to confirm whether SS used in non corrosive service may be susceptible to atmospheric...
  6. midris

    buried SS pipeline coating

    There are numerous types of phenolic epoxy coatings. Search for PPG's interactive catalogue online and read about the temperature limitations.
  7. midris

    Suitability of stainless steel in offshore applications

    The grade was not specified. Lets assume the two most common grades in this case, 304 and 316. Thanks
  8. midris

    buried SS pipeline coating

    You can use phenolic epoxy coating. It withstands temperatures nearing 200 degC. I have specified it for the external surface of liquid sulphur tank bottom plates where the operating temperture is 140 degC.
  9. midris

    Suitability of stainless steel in offshore applications

    Hello all, I work in an operating company in which I came across the below criteria for stainless steel: Stainless steel may be used in offshore applications up to an operating temperature of 60 degC. As per my understanding, the above temperature limitation governs in case of sour service...
  10. midris

    Insulation gasket between dissimilar metals in instrument air service

    Thank you Steve for the very informative response.
  11. midris

    Insulation gasket between dissimilar metals in instrument air service

    I understand what upset conditions are, however, I wanted clarity on what upset conditions are applicable to instrument air service. I asked earlier if there a probable risk of onset of galvanic corrosion due to moisture intrusion. Would corrosion be exacerbated by the attack of zinc from the...
  12. midris

    Insulation gasket between dissimilar metals in instrument air service

    Thanks Tom, There is no clear requirement apparently and thus we arent payed for it (we would have done it if the client payed for it). This was listed as a punch point and as you are aware we try discourage the client from making unjustified demands here and there. What do you mean by upset...
  13. midris

    Insulation gasket between dissimilar metals in instrument air service

    Hello, Our Client has asked for an insulation gasket where we have dissimilar material for the piping flange connection. In our case the flange connection is between SS instrument flange and galvanized pipe, while as per our drawings we have a graphite gasket. Is it required to provide...
  14. midris

    c p for aboveground storage tank

    Hi, The following parameters are required in order to determine the current requirement: - Type of coating of the storage tank bottom - Operating temperature of the tank - Surface area of the tank - A factor included in the surface area accounting for the surface area of the welds between the...
  15. midris

    Pump SDSS corrosion in sour water and chloride application

    Hello, A Client has asked for solutions to a corrosion problem they are having on an injection pump. Below are the process parameters: - Operating temperature is 54 degC - Sour water service - Chloride levels are in the 1000ppm order (definitely below 100,000pm) but not known exactly - MOC of...

Part and Inventory Search