Unfortunatly Is not a partial data report.
They tested and stamped every single part, i ve already considered your explanation but Is not my case.
Thanks
Good morning all,
Today i have a query about U Stamp and R stamp.
I have two equipment both of them are U stamped made by two differenti manufacturer, after the hydrotest and u stamped i have tò cut both of them and weld each other with a circumferential Joint.
This operation will be done on a...
Dear All
I'am trying to understand the design requirement for a pressure Vessel for Uzbekistan.
I understand that UzTr.427-019 is mandatory, but in that code i can not find information about the Design Code.
I've already worked for Russia project so i know GOST 34347 and GOST 34233, and i...
@RVAmeche: you have right, this explain everything. The one that made the stress put 0 on the anchor instead of 0.0001. So this explain everything.
@Novastark: The problem is the manufacturer of the condeser that declare an allowable load on the nozzle of 100N, 10kg.
This value is very low and...
Good evening or Good mornign everyone.
I kindly ask your support for a strange case in stress analysis.
Let me describe the problem
I have a condenser with very very low allowable nozzle load.
The external engineer that provide us the stress anlysis in Caesar provide us a strange results...
Thanks for the reply
The changing from BET to BEU was a deviation that i have already asked and it was approved.
Now the problem is the design code and the material
My question was based also on the material, i have sea water so SSDS, but if i select ASME VIII Div.2 as pe table Annex 3-A i...
Hi everyone
i got a problem with a Shell & Tube Heat Exchanger.
Shell side i got a design pressure of 14 bar(g) with water, on tube side i've got a design pressure of 210 bar(g)
The Customer ask me to supply a BET as per Tema!
Could it be? TEMA limit is 200 bar(g) but it's not clear if this...
Is that for Covestro project?
I did it with Sant'Ambrogio and no comments were issued.
If is this for Covestro, good luck, calculation is easy, but application of WN for bought material is quite hard and even QC control
Good morning everyone
I have a doubt about PED nameplate on a Super Heater.
Let me explain better
I am designing a Super Heater with final destination Belgium, so PED, 2014/68/UE, is applicable.
I have on my tube side, Steam, and is in category IV, module H1, instead my Shell has a pressure...
Good Morning, I have a question about the Appendix 47
I' am a certified Engineer from my country Authority, Italy, and I respect all the minimum requirement present in Appendix 47.
Based on above, my actual company proposed me as Designer from ASME Project U-STAMP.
I works in an Oil & Gas...
I agree with all of you, but this problem Is born due to my customer that cannot reply to my query and the only thing he said is to follow the specification.
The equation Is the follow: H = 1.3 * DESIGN PRESSURE * ( ALLOWABLE STRESS VALUE AT HYDROTEST TEMPERATURE / ALLOWABLE STRESS VALUE AT...
Good evening everyone. I got a problem with my new project for my new customer.
In his specification of pressure Vessel design he definines two ways for calculation of the hydrotest pressure: UG -99 (b) or an equation added to this specification. The two value obtain are quite different so which...
Thanks for your Replay.
Confirmed fire case, but only wetted case, not un-wetted.
I agree that temperature relieving Is the best choice
In case of there a Section about PRV or PSV i lo sai ti moderatore if can nove this thread on proper Section
Good Morning Everyone
In these days I got problem with one of my customer about selection of a PSV.
I got these data: T(Relief)=1094°F and T(Design of my component) = 649.4°F, with orifice E as calculated in accordance with API 520 Part. I
In accordance with API 526, using the temperature of...
I don't know.in his MR mi client has defined for the project to use ed. 2017.
But i gpt order in 2020. Maybe during bidding phase his MR was applied for the applicable edition of Asme.
I said him that i will use 2020 but he insist to use 2017.
Could be a problem with U stamp. I begin to...
