Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations waross on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: aqe1
  • Order by date
  1. aqe1

    Heat rise in a closed system

    I have 10 electrical components that carries a total of 350 watts inside a sealed .075" thk. steel box of 24"Hx30"Wx8"Deep. What would be the inside temp inside the box before heat starting to dissipate outside the box through convection with outside ambient temp of 50 degrees Centigrade.
  2. aqe1

    BREAK OUT VIEW

    WE ARE USING V5R7 SP2 CATIA AND I CAN'T CREATE A BREAK OUT VIEW WITH MOVING THE CUTTING LINE TOWARD THE LEFT SIDE OF THE CENTERLINE OF THE VIEW (NOTHING SHOWS) BUT IF YOU MOVE THE CUTTING LINE TOWARDS THE RIGHT SIDE OF THE CENTERLINE, IT WORKS. DOES ANYBODY KNOW OR HAVE ANY IDEA HOW TO DO THIS...
  3. aqe1

    Exporting .igs & step files

    And by the way, I am doing this on assembly, exporting igs and step files.
  4. aqe1

    Exporting .igs & step files

    Moldkon, Thanks for your reply. But I got another problem.I cannot change the setting on the dialog box to be paste with link. It selected paste. Do you know how to change the setup so I can change the setting to paste with link. Thanks again
  5. aqe1

    Exporting .igs & step files

    We are using Catia Ver5R7 and does'nt seem to work in exporting .igs & step files. Does anybody know? Thanks for your help in advance.
  6. aqe1

    DRAWING ENTITY

    I DON'T HAVE ANY PROBLEM DOING THE DUAL DIMENSION ON THE ASSY DRAWING. MY PROBLEM IS ADDING ENTITIES ON THE DRAWING MODE WHERE YOU CAN ALSO APPLY DUAL DIMENSION TO THESE ENTITIES. AND ALSO, HOW CAN YOU SHOW A LINE THAT IS OFFSET TO THE EXISTING EDGE OF THE PART?
  7. aqe1

    DRAWING ENTITY

    I AM DOING THE ASSEMBLY DRAWING. HOW AND WHAT CAN YOU ADD ON THE DRAWING THAT YOU CAN SHOW DUAL DIMENSION (INCH/MM). I SKETCH ENTITIES BUT IT ONLY GIVE SINGLE DIMENSION? THANKS FOR YOUR HELP
  8. aqe1

    Iges

    I also have the same problem converting proe .igs files to Catia V5R6 with Windows2000 operating system. Thanks for your help in advance.
  9. aqe1

    I made a plot plan for a new garage

    I made a plot plan for a new garage 20' wide x 18' deep on a R5 type contruction with a pitch roof. Now, buiding & safety requirements in our area (West Los Angeles, CA 90025) requires that I have to provide calculation for the size of the metal column to be used (located vertically on both...
  10. aqe1

    a flat roof.

    Anybody, is there someone (licensed structural engineer) you can refer? That would be a big help for a start. I am located in West Los Angeles, CA 90025 Also, I am getting tips from someone, saying, just run the the inside partition of the house (front to rear) all the way to the roof and put...
  11. aqe1

    a flat roof.

    I am planning to use wood, 2"x10" ridge and 2"x8" rafters on 16" centers without ceiling joist because I want to have vaulted ceiling. Now, my partition inside the existing house is not in the middle of 26'-0" width of the house. The partition that run from front...
  12. aqe1

    a flat roof.

    I have a house that is approx 988 sq ft (38x26wide) and has a flat roof. I want to change the roof of the house and plan of changing the roof with a pitch roof with bolted ceiling. My question is that what would be the size of the beam and span and what size of rafters and span I need. Thanks...
Back
Top