Search results for query: *

Another option would be Samarium Cobalt, which can easily accommodate that temperature range. The density is 8.4 g/cc, a little higher than NdFeB.

I recommend using the magnetic moment. Magnetic moment is the product of pole strength and magnet length. Cullity’s book describes it well: ‘Although pole strength and length are uncertain quantities individually, their product is the magnetic moment which can be measured precisely’. The...

DJI66: Did you intend this for the Magnetics Engineering forum? This might be a better question for the Welding forum: https://www.eng-tips.com/threadminder.cfm?pid=725

Clyde: If you need the measurement by a certified lab, I'd recommend Magnet Physics. They have a top-notch facility in Indianapolis: https://www.magnet-physik.de/en/

What type of magnet? It's straightforward for Alnico, most hysteresisgraphs have that functionality built in. I've run curves for various grades of Alnico with our equipment. It might be possible with a hard ferrite/ceramic. I don't think it could be done with SmCo or NdFeB.

Since you appear to be based in France, I'll recommend two companies in the European Union. Both of them make magnetizers that should work: In Germany, there is Magnet Physik: https://www.magnet-physik.de/en/ In Italy, there is Laboratorio Elettrofisico...

Arivel: You are looking for a superparamagnetic material. As far as I am aware, the only thing commercially available material are nanoparticles used for magnetic separation. I'm not aware of anyone selling them in bulk form suitable for a current sensor. Here is a link to one such provider...

Ben, I am still on A06 and enjoying it. I hope you re-join, we could use your expertise. I remember conducting Pass Through Tests on targets maybe 10 years ago. While it may not have been the best test, it was all the customer had available at the time and it did provide some quantifiable data...

I see both standards have been withdrawn, with no replacements. It would appear the committee overseeing them also saw problems with them. I'm not on the committee that developed those standards so I'm just speculating that 'magnetic conditioning' was done because the target will be magnetized...

The rated temperature is oftentimes called maximum operating temperature and it is more of a marketing concept. I don't like it very much, but it has gained widespread acceptance amongst laypeople. That said, when the concept was introduced it was defined as the temperature when a magnet with a...

If the Neo magnets are nickel plated, I've found out the hard way that temperatures over 400 degF can cause microcracks in the plating, leading to corrosion. It's not normally a problem if you are talking about an injection molding situation where the magnet is exposed to an elevated temperature...

Most steel manufacturers won't guarantee magnetic properties of their product, but you can get a general sense from some of the books listed in this FAQ: faq340-1436 Hopefully your school has some of these available. You are going to have to adjust your expectations a bit to match what is...

I don't believe so. Elevating the temperature will reduce coercivity but studies have shown coercivity doesn't play a huge role during magnetization for Neo. Assuming they are in the virgin state, a high coercivity Neo will fully magnetize at the same magnetizing strength as a lower coercivity...

Jpysam, In Case 2, if everything else stasys the same, the inner core will saturate earlier since it has less steel involved in the magnetic circuit. The total mmf will likely be less because of this.

Jpysam, Sorry, it sounded like you were designing a simple cylinder electromagnet. I didn't realize it was a round cup design. That said, the numbers for Case 1, with 88 kg appear reasonable, maybe a bit optimistic. I don't understand what you are describing in Case 2, can you provide a...

I modeled the first design in FEA and calculated 1.7 kg pulling force. For pulling forces, a single steel cylinder and coil is not the best geometry. One suggestion is to use a steel cylinder in a steel cup with a coil in between. These designs are much more efficient and there are a lot of...

Ed is correct. Epoxies generally work well with roughened surfaces. In my experience, acrylics work well with smooth surfaces. There are exceptions to both.

I concur with Ed. I would only add that most acrylic adhesives work best with smooth surfaces. You don't need a mirror surface finish on the steel but something reasonable that isn't going to drive the cost up.

Bruce, You're jumping a little too deep at this point. I recommend using the following FEMM example/tutorial, it'll help: https://www.femm.info/wiki/PermanentMagnetExample There are many, many other examples available on the FEMM Wiki. I recommend going through a number of them. They'll teach...

I made an FAQ for this: https://www.eng-tips.com/faq.cfm?pid=340 It is a bit dated but the link to FEMM is still valid and I recommend you start there, and utilize the examples provided. They have a large support group too.