Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!
-
GXDeveloper
Hi Mrbj Is it when you are editing online? or are you offline´? What is the exact message you get from the GX. Or can you upload a screen dump? I have had this problem once, but I can not remember what I did to get it right.' I have been trying to "force" the message you have told about, but...- Dariusch
- Post #3
- Forum: Programmable logic controllers (PLC)
-
Siemens SIMODRIVE
Hi hi.... I did not knew that... Sorry, but thank you Jraef for your response. To sume up, I got a big help from Skogsgurra. So thank you for that, Gunnar Best regards Dariusch- Dariusch
- Post #7
- Forum: Electric motors & generators engineering
-
Siemens SIMODRIVE
Hi Gunnar and Nikola, Thank you for the response. Gunnar the number for the drive 6SC6101 -2A- Z Z= 2xA20+G10. Nikola the drawings for the 6SC85, does not look alike the 6SC61. I will search for "Relcon". Thank you for the time Dariusch- Dariusch
- Post #4
- Forum: Electric motors & generators engineering
-
Siemens SIMODRIVE
Hi everyone, I have a Siemens SIMODRIVE 6SC61-01-2A-Z (it is an old drive 1989)that is controlled by a SINUMERIK (Also old 1989). Now I would like to control the SIMODRIVE with a mitsubishi PLC, so I don't have to use the SINUMERIK. My question is, Where can I find some material/manuals for...- Dariusch
- Thread
- Replies: 6
- Forum: Electric motors & generators engineering
-
OLD Mitsubishi A0J2
I have a problem with an A0J2-PLC. I was called out to a customer who has a machine with an A0J2-PLC. First there was no power to the PLC, I turned the power on, but then the "RUN"-led flashes slowley. I tryed reset but it did not help. The I tryed to communicate trouht GX-Developer...- Dariusch
- Thread
- Replies: 2
- Forum: Programmable logic controllers (PLC)
-
App. with 5 encoders
Thank you xyzz! Why didn't I think of that! You have been very helpful thanks again. mvh. Dariusch- Dariusch
- Post #9
- Forum: Programmable logic controllers (PLC)
-
App. with 5 encoders
Hej xyzz. My system is of A1S, and have only 1 slof free so if I want to use High-speed indput I have to bye an extentionboard and 3 High-speed card. So instead of that i thought of using Profibus, only 1slot. Also there woulden be so mutch cabeling. The frequencie is about 1 rpm./min...- Dariusch
- Post #7
- Forum: Programmable logic controllers (PLC)
-
App. with 5 encoders
Hi xyzz. Thank you a lot for all the explanation. But I have one question more. What do you think of using profibus instead of High-speed indput??- Dariusch
- Post #5
- Forum: Programmable logic controllers (PLC)
-
App. with 5 encoders
"Do you need the quadrature mode for every encoder? Hardware reset?" Im sorry, but I don't know what you mean by "quadrature mode". It is for a machine for polishing sink/washbasin, and there are diffrent kind of these, so there have to be 10 different porgrams, one for...- Dariusch
- Post #3
- Forum: Programmable logic controllers (PLC)
-
App. with 5 encoders
Hi. I am doing a application with 5 encoder for positioning. I have a Mitsubishi A1SH. What is the best thing/way for handeling 5 encoder, when i have to read data for all 5 encoder at the same time? I thought of using profibus? Does someone have any ideas??? Thank you Dariusch- Dariusch
- Thread
- Replies: 8
- Forum: Programmable logic controllers (PLC)
