I am currently trying to model the pressurized release of air from a 1000 psi tank into a chamber. I'm currently using Density-based settings because I couldn't seem to get a solution when I used Pressure-based settings.
This is how I initialized the problem:
1) Set everything as a wall...
I know I posted a similar question, but I think I have a clearer explanation of what I want to do.
I basically want to model a shock tube, where pressurized air is kept behind a diaphragm in an enclosed tube, and at t=0 the diaphragm bursts and the pressurized air propagates in the enclosed...
*through. I have been reading up a little and I believe it's something to do with mass transfers, but I can't seem to find any tutorials (or at least, my school doesn't have them on the computer) that can help me out.
Hi all, I am extremely new to ANSYS Fluent so pardon me if these questions are very basic. Basically I want to model the flow of a fixed amount of air in a pressurized gas tank throw a pipe and into a chamber using Fluent, how would I go about doing this?
I currently just have the chamber...
yeah i looked for "gold stress-strain curves", "gold stress-strain data", "gold tensile stress-strain". Most of the results that came up were for gold film (which I could theoretically use, but the mechanical properties may differ slightly), or gold fibers embedded in other materials and...
I've found stress-strain curves, but I would need specific values for gold in order to input them into my model. Did you happen to come across a specific one for gold?
Yeah that's what I was thinking since gold is isotropic, but at some point in my compression modelling it is bound to experience plastic deformation so I was wondering if there is any way to model that.
Is there any catalog out there which has stress-strain data for materials? I found Boyer's...
I am currently modelling the transverse compression of a gold fibre using FEA software, and I was wondering what plasticity model would be good. I'm thinking of using Johnson-Cook's plasticity model, but I then have no idea where to get the necessary parameters. If there is no good model, where...
I'm using ABAQUS Explicit, simulating a dynamic pressure load within a confined box. I tried outputting the Mises stress at the inner corner node, and the output I'm getting has these huge vibrations (as attached). I'm not sure what this is, it's probably something to do with finite element...
Hmm I don't think so, seeing as I am not advanced enough to do that yet. I basically followed this
http://www.tu-chemnitz.de/projekt/abq_hilfe/docs/v6.12/books/gsa/default.htm?startat=ap05s06.html
Flow through a bent tube, but I modified the parameters for my case as necessary. The only thing...
I do have all 8 processors running, I'll try to run it with 6 and see how that goes, but I'm currently at my wits' end if that doesn't work. Does Simulia offer over-the-phone help or do they just have the knowledge base? Because I spent about 20 minutes figuring their website out and I gave up.
Other jobs have run fine, but this is the first co-sim that i've run on this computer. It has 32Gb RAM and 8 processors, so it should at least run, even if slowly. I just don't understand why it just stops responding.
Come to think of it, it might actually be a networked license. The command...
Hi IceBreakerSours,
First off, thanks for your response in both my threads, you've been a major help. I'm currently running a local installation of ABAQUS 6.12 Research Edition on my lab computer, but the problem keeps surfacing at approximately the same point. I have had solutions blow up so I...
I have no idea why this happens, but I've been pounding at this the whole night. I have a Fluid-Structure co-simulation all set up and ready to run. It does ok for about 3000 iterations, and then at a certain total time ABAQUS stops responding. What does this mean when this happens, is the...
THANK YOU SO MUCH. I've been trying to search the knowledge base for a fix but I can't. I might have a copy of Explicit in my school's computer, I might try that later.
Otherwise, based on whatever I've done so far, should it theoretically work in Explicit?
No, I know there's no two reference nodes required for environment interaction but somehow ABAQUS (I'm using 6.13) wants it. I uploaded a screenshot to show what's happening.
I have a fluid cavity inside a cylinder (Interaction Property cavity, Interaction first cavity), the fluid exchange with...
Hi akabarten, thanks for your response.
I followed the user manual at every step, but it just doesn't mention anything about having two reference nodes. I'm thinking of just making a huge tank to act as the "environment" for now just so I can get the project moving along.
It doesn't help that...
