Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations waross on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. mazakoper

    Jagged Edge on SS w/N2 assist

    O8021 (24GA SS ALL 7.5 LENS) G82P1500Q200R35 G88P55M58 G87P0 M32 M20 M22 G04X0.2 G82P1500Q100R100F200 G04X0.1 M99 O8022 (24GA SS ALL 7.5 LENS) G82P1500Q200R35 G88P55M58 G87P0 M32 M20 M22 G04X0.2 G82P1500Q100R100F200 G04X0.1 M99 O8030 (22 GA SS SKEL 7.5 LENS) (NF -0.04 0.077 NOZ) G82P1000Q150R15...
  2. mazakoper

    Jagged Edge on SS w/N2 assist

    THESE ARE A 5INCH LENS O8021 (24GA SS 5.0 LENS) G82P1500Q200R35 G88P55M58 G87P0 M32 M20 M22 G04X0.2 G82P1500Q100R100F260 G04X0.1 M99 O8022 (24GA SS 5.0 LENS) G82P1500Q200R35 G88P55M58 G87P0 M32 M20 M22 G04X0.2 G82P1500Q100R100F260 G04X0.1 M99 O8030 (22GA SS 5.0 LENS) G82P1000Q150R15 G88P10M56...
  3. mazakoper

    Jagged Edge on SS w/N2 assist

    DID IT WORK FOR YOU IF NOT TRY TO ACCELERATE AFTER LEAD IN. YOUR LEAD IN SHOULD BE ONE THIRD OF YOUR FEAD RATE
  4. mazakoper

    can you cut 1/2" mild steel

    (.500 HRS NTX 1.5KW) (NF EVEN 0.077 NOZ) G88P5M56 G87P2 M32 M20 G82P1500Q10R18 M22 G04X1.0 G82P1500Q35R25 G04X1.5 G82Q70R32 G04X2.5 G82Q90R39 G04X3.0 G82Q110R46 G04X8.0 G88P4M56 G87P9 G04X0.2 G82P1500Q700R100F27 G04X0.1 M99 THESE PARAMETERS ARE FROM MAZAK NEVER USED IT BUT IT WILL GET YOU...
  5. mazakoper

    I am in need of peramiters

    Material ID Size Beam On Pre-LO Post-LI G078480096 -1.000 M98P6105 G078480096 0.001 M98P6105 G078480096 0.100 M98P6100 M23 M98P6101 G078480096 0.500 M98P6100 M23 M98P6102 G078480096 99.000 M98P6100 M23 M98P6102 THIS IS HOW WE ACCELERATE BEAN...
  6. mazakoper

    I am in need of peramiters

    DID YOU TRY TO LOWER YOUR FOCUS.AND DID YOU TRY TO ACCELERATE WHEN CUTTING 14 GA. AND THICKER YOU HAVE TO START OUT SLOW ON YOUR LEAD IN THAN GO FASTER.
  7. mazakoper

    I am in need of peramiters

    THESE ARE MY CUT CONDITIONS FOR A 5 INCH HEAD (24GA SS 5.0 LENS) G82P1500Q200R35 G88P55M58 G87P0 M32 M20 M22 G04X0.2 G82P1500Q100R100F260 G04X0.1 M99 O8022 (24GA SS 5.0 LENS) G82P1500Q200R35 G88P55M58 G87P0 M32 M20 M22 G04X0.2 G82P1500Q100R100F260 G04X0.1 M99 O8030 (22GA SS 5.0 LENS)...
  8. mazakoper

    Jagged Edge on SS w/N2 assist

    I dont know if you tried this but lower your focus that usally takes care of it.
  9. mazakoper

    using a 5 inch lens

    Ive been using a mazak laser for ten months. I was using a 7.5 inch lens.I just changed over to a 5 inch can someone give me tips on how to keep parts from moving so i can cut faster.
Back
Top