Fiber Laser: Blasts logos and barcodes like a champ! Loves metal, plastics, even wood! But, can get a bit hot-headed...
UV Laser: Whispers intricate designs with a delicate touch. Hugs fragile materials like glass and electronics. But, takes its time with thicker jobs... ❄️
share your...
Here are some suggestions you can try:
Inconel spatter fix:
Try Inconel-specific anti-spatter: Stronger adhesion for this tricky metal.
Double coat: Thin layers might cling better than one thick one.
Nitrogen assist gas: Can shield the cut and potentially reduce spatter.
Cardboard shields...
Because 310SS and 308SS filler metal have different alloy compositions, welding 310SS material with ER308/308L filler metal may cause problems. Although the impact may be minimal in your case because the design temperature is below 1000°F, it's still important to take into account possible...
One common solution is to drill a small hole (about 1/16") near the weld on the side of the socket. The hole can be used to purge the oxygen with an inert gas, such as argon. Once the oxygen has been purged, the hole can be plugged with a weldable plug or capped with a small piece of pipe...
It's wonderful that you've acquired a second-hand H-LASE fiber laser source. If you need a manual for this specific type of laser source, I recommend reaching out to the manufacturer directly. You can typically find contact information on their official website or by searching for their customer...
I understand the importance of having the right equipment. Now, when it comes to cutting stainless steel, precision is key, and you want a machine that's not just reliable but also efficient. Let's discuss the features and other important aspects for this.
ello and welcome to the community!
It's great that you're seeking best practices for installing JIC/AN fittings, and your questions are quite detailed. Here are some insights that might help:
Use of Gaskets like SECO seals:
SECO seals can be beneficial in high-pressure systems, and using them...
It's great that you're considering the practical aspects of your design. When dealing with openings in reinforced concrete elements, especially in cases where only a small portion of the column is carrying the vertical load, it's crucial to assess the structural integrity and redistribution of...
Handling stress concentrations in your motor shaft transition can be tricky. To tackle this, consider using the notch sensitivity factor ('q') and exploring the stress concentration factor (Kt) specific to your design. These factors provide insights into fatigue life and the severity of stress...
Dealing with Heat-Affected Zones (HAZ) in aluminum laser cutting can be challenging. Opting for the right laser parameters and techniques is crucial to minimize HAZ and ensure clean, precise cuts.
I understand your frustration, especially when you've successfully done test cuts but encounter issues during the actual cutting process. It could be related to the settings in your program. Make sure you've double-checked the feed rates, power settings, and focus for your machine. Additionally...
Hey,
Try this out hope this will help!
It sounds like you might be experiencing issues with your laser cutter's origin point. To fix this, check if there's an option in your machine's settings to disable origin point cutting or make sure your DXF files have the correct origin point. This...
Hey Waqas,
Hope you are doing well!
Welding thin stainless steel (0.5 mm) without burn-through:
1. Reduce laser power.
2. Use pulse mode if available.
3. Slow down welding speed.
4. Maintain a steady hand.
5. Consider using filler material.
6. Back purge with inert gas.
7. Optimize joint...
Hi Sir,
Hope you are doing well!
Using nitrogen, helium, and CO2 gases, the laser's resonator produces the cutting beam. These gases must be purified at the input before entering the resonator, and their purity grade must be 5.0 or above. The three components of the resonator gas may be...
Stainless steel is a corrosion-resistant alloy of iron, chromium and, in some cases, nickel and other metals. Alloy steels are made by combining carbon steel with one or several alloying elements.
When we purchased the machine most of the people worry about any issue that might arise in the machine after the delivery. What are you thinking about support and customer care support for quarry about machine.
