Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: XELR8
  • Order by date
  1. XELR8

    ASME VIII High Strength Stainless

    Look at adding gussets perpendicular to the lug for reducing the stress on the "lug". If the hole size of the clevis pin is of concern add a pad plate to lug. Use a clevis through the clevis of the lug to reduce the moment on the weak axis of the lug. Can you describe how you calcualted the...
  2. XELR8

    ASME VIII High Strength Stainless

    Hi TGS4, Thanks for your information and clarification. I understand the ASME Code and your point. I was not trying to answer the ASME Sec VIII code but rather what would work if your outside of the code rules already? Why was the clip under designed per ASME Code Sec VIII in first place...
  3. XELR8

    ASME VIII High Strength Stainless

    Here are a few suggestions: 1) Check your material certificates for your 304 plate and see what the actual tensile strength is. You can use this as your value. 2) Check the strain at your calculated stress and see if its less then 2%. If it is your probably ok. 3) What stress is high, primary...
  4. XELR8

    California Seismic Code Retrofit

    Ok I will check out the California Building Code and make sure the current amendments are included. I will also call the building department for their requirements. Thanks!
  5. XELR8

    California Seismic Code Retrofit

    If I am going to put a 2 inch hole in a the wall of a CMU block building built to 1965 code do I have to redesign or modify the entire building to current day standards because it was modified? I understand the local building departments involvement and I greatly appreciate your response cvg. I...
  6. XELR8

    California Seismic Code Retrofit

    I want to know what Code requires design retrofit for buildings in the state of California. I am modifying a small building that was built in 1965 and I want to know if the entire building needs to be upgraded and what code allows/exempts required changes.
  7. XELR8

    302 SS Compatability Properties

    I am curious in understanding what makes 302 Stainless Steel bleach compatible. I have made experiments with small springs made from 302 SS that have not corroded. Is the 302 steel resistant to oxidation from hypochlorite (OCl-) or is it resistant to the hydroxide (OH-)? How is 302 steel...
  8. XELR8

    Temperature and Heat

    ok, got it! Thanks!
  9. XELR8

    Temperature and Heat

    Compositepro, sorry, I meant to say higher temperature to lower temperature. I just wrote it wrong. Thanks for correcting me. To all, even though the temperature is rising for the cooler material and is still less then T high. I am sure there is a conduction within the object at T low absorbing...
  10. XELR8

    Temperature and Heat

    Great information and insight but are you talking about temperatures below the heat supply temperature and probably not perfectly insulated from other cooling/heating source like radiation or convection, if possible? I still think the heated object temperature (object at lower temperature) can...
  11. XELR8

    Vent Requirements

    I am in agreement with your statements about older installations and vent calculations are documented that way in NFPA 68 2007 also. Good chat and I appreciate the help.
  12. XELR8

    Vent Requirements

    About the calculation, if the methods for determineing required vent area have changed from the new NFPA 68 2007 edition is it realistic to say that the old calculation is no longer valid? Would it be fair to compare the new calcualted vent area vs an existing vent area that may have been...
  13. XELR8

    Vent Requirements

    I agree that Silos indoors need to be vented per NFPA 68 2007 but do the Silos outdoors away from personnel need to be vented as well? NFPA says, all combustible dust enclosures should be located outdoors. If they are indoors they should have vent protection as per the standard. It "NFPA" does...
  14. XELR8

    Temperature and Heat

    Hi IRstuff, Information noted and confirmed. Thanks.
  15. XELR8

    Temperature and Heat

    Hi Expert Help, So, a material when heated (properties willing) can reach the same temperature of the heat source and can never exceed the temperature of the higher temperature heat source? This assumes the higher temperature source has an infinite supply of energy to remain constant. ( I...
  16. XELR8

    Vent Requirements

    Hi psafety, Thanks for your response. I have the same understanding from the NFPA Standard. Does the owner accept the risk or the AHJ? It seems to me that the AHJ would never accept any risk for loss of equipment or any possible safety risk. Do you have any feel for industry standards on...
  17. XELR8

    Temperature and Heat

    I really enjoy the answers and related views. So let me ask this, why can rubbing two sticks together at a lower temperature create a flame at a higher temperature. Please, note, I understand combustion but it does flaw some earlier answers. Thanks!
  18. XELR8

    Temperature and Heat

    Hi Folks, Thanks for your help and quick response. No tricks, you answered my question. I thought the answer would be no, you can never exceed the temperature of the source but, I could not document any physical or scientific equation with the theory. Feel free to add any further comments.
  19. XELR8

    Temperature and Heat

    Will an object that is heated ever get to a higher temperature then the heat input temperature itself. For example, if I heat a piece of metal with a heat source at 150F, will the temperature of the metal ever exceed 150F if the heat source input remains constant for a long period of time? Thanks!
  20. XELR8

    Vent Requirements

    Do dust collectors located outside of buildings require vent protection per NFPA 68? If so, what paragraph in the NFPA 68 Standard references this requirement? Thank you!

Part and Inventory Search

Back
Top