Nov 10, 2011 #1 ZJLombard Structural Nov 10, 2011 4 0 0 ZA Good afternoon, Does anybody have problem using NX 7.5 and a SpacePilot Pro 3D mouse? I am running the latest drivers for the SpacePilot and it is still very sticky when I rotate? I would realy appreciate any advise! Regards, Zach
Good afternoon, Does anybody have problem using NX 7.5 and a SpacePilot Pro 3D mouse? I am running the latest drivers for the SpacePilot and it is still very sticky when I rotate? I would realy appreciate any advise! Regards, Zach
Nov 10, 2011 #2 JohnRBaker Mechanical Jun 1, 2006 35,347 2 38 US I don't have any problems and the 3DxWare version I'm running is 6,11,1,0. John R. Baker, P.E. Product 'Evangelist' Product Engineering Software Siemens PLM Software Inc. Industry Sector Cypress, CA http://www.siemens.com/plmUG/NX Museum: http://www.plmworld.org/p/cm/ld/fid=209 To an Engineer, the glass is twice as big as it needs to be. Upvote 0 Downvote
I don't have any problems and the 3DxWare version I'm running is 6,11,1,0. John R. Baker, P.E. Product 'Evangelist' Product Engineering Software Siemens PLM Software Inc. Industry Sector Cypress, CA http://www.siemens.com/plmUG/NX Museum: http://www.plmworld.org/p/cm/ld/fid=209 To an Engineer, the glass is twice as big as it needs to be.
Nov 10, 2011 Thread starter #3 ZJLombard Structural Nov 10, 2011 4 0 0 ZA Thank you very much for your feedback. Atleast now I know that it is not the spaceball. Our IT department blames the spaceball, which it is not! Thank you! Regards, Zach Upvote 0 Downvote
Thank you very much for your feedback. Atleast now I know that it is not the spaceball. Our IT department blames the spaceball, which it is not! Thank you! Regards, Zach
Nov 11, 2011 #4 FrankHa Mechanical Oct 21, 2009 12 0 0 SE What do you mean with "Sticky"? Could it perhaps be that "Dominant Axis" is enabled? (So if you rotate in 2 directions at the same time with the hand, only one is rotated on the computer) Frank Hagström http://www.conex.se Upvote 0 Downvote
What do you mean with "Sticky"? Could it perhaps be that "Dominant Axis" is enabled? (So if you rotate in 2 directions at the same time with the hand, only one is rotated on the computer) Frank Hagström http://www.conex.se
Nov 15, 2011 Thread starter #5 ZJLombard Structural Nov 10, 2011 4 0 0 ZA Good morning FrankHA, When I rotate mthe model with the spaceball, it doesn't rotate freely. It will rotate a bit and then stop for a moment and then rotate again. The "dominant Axis" is disabled. Our local NX supplier came to our office to have a look. They think it might be that our pc's are under spec for what we are trying to do. Not sure but only time will tell. We are going to upgrade my pc to find out if that is the case. Thank you for your responce! Regards, Zach Upvote 0 Downvote
Good morning FrankHA, When I rotate mthe model with the spaceball, it doesn't rotate freely. It will rotate a bit and then stop for a moment and then rotate again. The "dominant Axis" is disabled. Our local NX supplier came to our office to have a look. They think it might be that our pc's are under spec for what we are trying to do. Not sure but only time will tell. We are going to upgrade my pc to find out if that is the case. Thank you for your responce! Regards, Zach