nx 8 hole table problem

[PROTYzara]

The hole table in nx 8 will not produce a table. It seems the there are missing buttons on the menu (differ from nx6). I follow the procedure (unlike the old table there is no button to hit) to create the table....so i hit apply and nothing.
WHERE am I going wrong?

Below is a pic of the hole table in ug nx8.

http://files.engineering.com/getfil...149-db1ed00c0b56&file=hole_table_menu_nx8.JPG

 

[JohnRBaker]

I just tested this using NX 8.0.1.5 and it worked fine.

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.

 

[PROTYzara]

Please send a pic of your menu and the procedure you follow.

Thank you.

 

[Arkance/PhoeNX]

work fine for me to and my hole table dialog looks exactly the same as the image posted.

Anthony Galante
Technical Resource Coordinator

NX4.0.4MP10, NX5.0.6, NX6.0.5, NX7.0.1, NX7.5.0-> NX7.5.5 & NX8.0.0 -> NX8.0.1

 

[JohnRBaker]

Attached is a video of a Hole Table creation session in NX 8.0.1.5.

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.

 

[PROTYzara]

thank you!!

 

[PROTYzara]

there most be something wrong my with lic or something cause it will pick the point, select the circles (or view) and then drop the orgin... hit ok and NO table in the drawing. NO CLUE.

 

[JohnRBaker]

Time to call GTAC.

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.

 

[frankbe]

Could it be that the table output was made on an invisible layer?

2x NX8.0.1.5 Mach Design
1x Solid Edge ST2

 

[PROTYzara]

GOT IT!

If you open a file thru convertion (i.e. step, igs, ect.) the file sometimes creates its holes has a feature not a single hole thus the table see's no holes for the table.

Thank you for your help.

 

[PROTYzara]

UPDATE:

Come to find out that the hole table problem with the converted files was a NX 8.0.0 problem that GTAC knew about. They corrected it in update NX 8.0.1

 

[JohnRBaker]

NX 8.0.1.5 is available for download so let's get going, eh?

John R. Baker, P.E.
Product 'Evangelist'
Product Engineering Software
Siemens PLM Software Inc.
Industry Sector
Cypress, CA

http://www.siemens.com/plm

UG/NX Museum:

http://www.plmworld.org/p/cm/ld/fid=209

To an Engineer, the glass is twice as big as it needs to be.