Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations KootK on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Sky pool! 1

Status
Not open for further replies.

MIStructE_IRE

Structural
Sep 23, 2018
816
As much as this image looks like CGI, its not. Its just opened in London and appears to be made of 200mm thick acrylic. The span is about 14m and it consists of a 200mm thick acrylic slab spanning between upstand beams. These beams are 200mm thick acrylic x 3.3m high!

I’m still unsure as to why the compression zone of these incredibly slender upstand acrylic beams does not LTB itself into oblivion! I understand the concept of U-frame action in chunky steel bridges, but this seems to defy all understanding I have of structural behavior! Can anyone shed some light on this? Its very impressive!

Ps - for those wondering about redundancy, as I was, there are 2 No. steel cables beneath the slab..

F75E9798-47DB-4F40-9434-E9EA3A5530EE_ubn88t.jpg


D06BDBD3-2430-4FF7-B41F-F4089BA2FC1F_qrc0nq.jpg
 
Replies continue below

Recommended for you

"Transparent Aluminium" or "Transparent Aluminum"

Referencing Star Trek IV.

It clearly works.

I wonder what they do about rain water? Presumably the water level would increase during a storm event. I wonder if they have designed for the 2.55m water depth or if they have an overflow somewhere? and if it does overflow, where do they put it, through the down pipes and into the sewerage system?

Cleaning the outside will be fun job for someone.
 
Ussuri said:
I wonder if they have designed for the 2.55m water depth or if they have an overflow somewhere?

Within the building it's a regular pool edge, a few hundred mm above the water. So it can't build up more than that.

pool_dumuh0.jpg
 
Tomfh said:
I'm not sure how those cables could hold up the actual pool.

I was thinking that, when required, the tendon springs would introduce enough sag into the tendon profiles that they could hold up the pool as catenarys. I don't know enough about the anchorage situation to know if that's realistic though. And your water tightness theory certainly seems reasonable to me as well.
 
Are we thinking that there's a movement joint at every one of those yellow rectangles?

C01_ngt6pg.jpg
 
yellow rectangles ? = red clouds ??

another day in paradise, or is paradise one day closer ?
 
KootK said:
The yellow rectangles within the red clouds.

I think just at the yellow rectangles each end of the acrylic. Acrylic has a high coefficient of thermal expansion.

 
I think they are calling out movement bearings at all 4 (or, perhaps, 8) points. When then acrylic expands or contracts, you want the whole of the stainless tubs on either side to move with it to maintain a watertight seal. If the stainless is restrained at both ends and the acrylic contracts, it could pop the seal between the two.
 
The bottom slab thickness is quoted at 380mm, not 200 as in the OP. Might make a difference.

I can see the sway and movement working on sliding supports, but wasn't quite so sure about if one building went up or down.... Looks like a chance of a leak there alright.

image_vqwqfd.png


Remember - More details = better answers
Also: If you get a response it's polite to respond to it.
 
I'm travelling regularly to London. I was going to mention that I'd check out this sky pool,
but seeing the website I believe my pockets aren't deep enough to visit this pool...
It is however right south of the Thames at the center of London, so most likely visible from the public streets. I'll take a zoom lens with me next time...

Have a look at that site, the water top level sits at about 80 cm below the top of the acrylic walls (2 ft 8")
 
You mean you can't swing 1,500,000 USD for a 2 bedroom apartment on an engineer's salary?
 
Thanks phamENG for confronting me with reality, and thanks to whomever starred that post for depressing me even further...
 
You mean you can't swing 1,500,000 USD for a 2 bedroom apartment on an engineer's salary?

That sounds like a great deal! There are condos in SF that go for that amount without the pool and glitzy women [banghead]

TTFN (ta ta for now)
I can do absolutely anything. I'm an expert! faq731-376 forum1529 Entire Forum list
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor