Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations GregLocock on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

m_ridzon
  • Locked
  • Question
Response Spectrum Results from FEA for BPVC Qualification
Replies
0
Views
86
m_ridzon
m_ridzon
Ing. Aponte
  • Locked
  • Question
ASME VIII div. 1 - Weld efficiencies 1
Replies
3
Views
480
SnTMan
SnTMan
DAVB
  • Locked
  • Question
UG-42 (a)(1)- Reinforcement of multiple openings
Replies
1
Views
122
GD2
GD2
mrmyagi
  • Locked
  • Question
What does g1 and g2 represent in EN13445-3 table A-7 figure F4 ?
Replies
2
Views
105
mrmyagi
mrmyagi
m_ridzon
  • Locked
  • Question
Simplification of 3D Solids to 2D Shells for Pressure Vessel
Replies
4
Views
99
m_ridzon
m_ridzon
Digitall
  • Locked
  • Question
Time dependent properties for SA-516 Gr.70 2
Replies
7
Views
323
TGS4
TGS4
skengg
  • Locked
  • Question
NON STANDARD FLANGE DESIGN AS PER ASME SEC. VIII DIVISON 1 V/s DIVISON 2 9
Replies
10
Views
337
GD2
GD2
FPPE
  • Locked
  • Question
Pressure thrust for AES HEX process inlet and outlet nozzles 3
Replies
10
Views
200
FPPE
FPPE
FPPE
  • Locked
  • Question
Pressure thrust in PV elite
Replies
3
Views
222
FPPE
FPPE
Bjorn Nilsson
  • Locked
  • Question
ASME PCC-2 Article 212 Fillet Welded Patches
Replies
0
Views
223
Bjorn Nilsson
Bjorn Nilsson
Packermanfan
  • Locked
  • Question
FFSO Flange Clarifications 2
Replies
10
Views
345
jt1234
jt1234
mrmalcolm
  • Locked
  • Question
Toughness required by the EN 13445
Replies
0
Views
166
mrmalcolm
mrmalcolm
FPPE
  • Locked
  • Question
ASME VIII Tubes expansion percentage limit to be considered in calculation
Replies
1
Views
187
EdStainless
EdStainless
pvros
  • Locked
  • Question
Fatigue screening - Method B - ASME VIII Div.2 Ed. 2023
Replies
2
Views
366
GD2
GD2
RadiateurFou
  • Locked
  • Question
Can old Appendix 1-10 still be used for large openings? 2
Replies
17
Views
258
jt1234
jt1234
mechengineer
  • Locked
  • Question
Test weight factor for davit arm of flange cover of heat exchanger or 24" manway
Replies
3
Views
134
r6155
r6155
MchDesign
  • Locked
  • Question
UCS-66 / ASME SA-516 Gr.70 Fine Graine Practice
Replies
2
Views
204
david339933
david339933
UMSsp.z o.o.
  • Locked
  • Question
Titanium pipe connection 1
Replies
4
Views
184
UMSsp.z o.o.
UMSsp.z o.o.
PMCap
  • Locked
  • Question
Tangential nozzle 2
Replies
15
Views
304
david339933
david339933
K_macisaac
  • Locked
  • Question
API 579 ffs Fixing Negative RSFpit
Replies
3
Views
187
danb3
danb3
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom