Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations GregLocock on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Gear and Pulley engineering

Ivan Silva
  • Locked
  • Question
Lubrification on sprocket gear
Replies
3
Views
83
Ivan Silva
Ivan Silva
Galvano
  • Locked
  • Question
Doubt about plastic gears 3
Replies
10
Views
119
Compositepro
Compositepro
Galvano
  • Locked
  • Question
Doubts about the operation of a clutch 2
2
Replies
34
Views
251
Galvano
Galvano
BrianE22
  • Locked
  • Question
Ductile Iron for worm gears? 2
Replies
8
Views
300
BrianE22
BrianE22
OfficialGreenTea
  • Locked
  • Question
Contact ratio of spur gears with varying centre distance
Replies
7
Views
404
OfficialGreenTea
OfficialGreenTea
redlee
  • Locked
  • Question
Gear Blank Help.
Replies
12
Views
104
redlee
redlee
Ryan.z
  • Locked
  • Question
ASA I Sprocket Standard???
Replies
1
Views
107
desertfox
desertfox
MonsterMaxx
  • Locked
  • Question
25T 1.0 Mod Gear came out wrong. How to measure 'over the wires'? 1
Replies
13
Views
165
mfgenggear
mfgenggear
Ryan.z
  • Locked
  • Question
Why have big different between KissSoft & MITcalc???
Replies
1
Views
112
mfgenggear
mfgenggear
matts05
  • Locked
  • Question
Worm Gearset Design -- Pressure Angle & Tooth Bending Strength
Replies
4
Views
250
spigor
spigor
NJAus1
  • Locked
  • Question
Gear Train Deceleration
Replies
3
Views
65
SwinnyGG
SwinnyGG
703Y
  • Locked
  • Question
Pulley ratio
Replies
2
Views
87
703Y
703Y
md0501
  • Locked
  • Question
Custom Gear Involute Cutter
Replies
7
Views
96
spigor
spigor
md0501
  • Locked
  • Question
Planetary Gear Help! 2
Replies
12
Views
360
Windward
Windward
jarimasen
  • Locked
  • Question
Visual inspection for open gear guide
Replies
5
Views
104
3DDave
3DDave
TugboatEng
  • Locked
  • Question
Gear Corrosion 1
Replies
12
Views
152
mfgenggear
mfgenggear
Govardhanan
  • Locked
  • Question
Calculating the force required / Design of rack and pinion
Replies
2
Views
71
Govardhanan
Govardhanan
Suryakanth
  • Locked
  • Question
Is it mandatory to use Helical gears(drive-driven) as a set? Is mix usage OK?
Replies
3
Views
139
geesamand
geesamand
sheafromme
  • Locked
  • Question
Securing pulley to stepper motor shaft
Replies
9
Views
163
TugboatEng
TugboatEng
Ivan Silva
  • Locked
  • Question
Is splined shaft suitable to simultaneous axial and rotational motions? 2
Replies
9
Views
270
romke
romke
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom