Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

  • Congratulations IDS on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by JAS

  1. JAS

    How to reduce thickness because of Full vacuum

    Dear All, The present condition of the ALREADY FABRICATED COLUMN has FULL VACUUM with 6mm CA. The information did not pass on to the Vendor and the Column has been fabricated considering PARTIAL VACUUM. So only the top Shell course & Head fails because of less thickness (Fabricated 18mm with...
  2. JAS

    Travelling Speed of a Floating Roof

    Thank you LittleInch...
  3. JAS

    Travelling Speed of a Floating Roof

    Hello everyone, We have already discussed many times in this forum regarding the Travelling Speed of a Floating Roof. All are generic answers and based on experience. Iam designing few Tanks and was asked the Travelling speed of the Floating Roof to judge the wear & tear (including for the...
  4. JAS

    The Suitable Q275 Grade for tank design

    hi, Check this website: https://www.chinesesteelgrades.com/q275-steel/ Thanks, JAS
  5. JAS

    ASME VIII - Dent vs Out-of-roundness

    Hello, Out-of-roundness is the difference between the maximum and minimum diameters at any cross section. Yes, you are right-->out-of-roundness shall be measured on full length of a shell section/course. A dent is a permanent plastic deformation of the circular cross-section of the Shell. A...
  6. JAS

    is there any criteria to select the type of tank roof

    Hello, API 650 does not mention the criteria for the selection of Roof types. Generally, Roof types depends on the Size (dia) of the Tank, Liquid stored, Hazardous etc,. for example, If the vapour pressure is more and if there is a possibility of forming a Vapour cloud above the liquid surface...
  7. JAS

    Design of rectangular pressure vessel with orthogonal stiffeners

    Hi, refer "Formula for Stress and Strain" by "Roarks and Young" for the design of Rectangular Tanks.
  8. JAS

    API 650 Section 8.1 Method of examining joint

    Hi, Section-8 is for Method of Examining Joints and explains about RT, UT, MP, LP, Visual, Vacuum. Method of RT is same for all Tanks. There are other tests in case if RT is not possible. The quality of the Radiography film speaks about the Welder's performance. You may refer to 8.1.2.5 /...
  9. JAS

    Distance Between Intermediate Wind Girders

    hi, the only interpretation used by API 650 is by calculating H1 (5.9.7.1) & Wtr (5.9.7.2) and check whether Wtr is > H1. The ratio of Wtr/H1 provides the required quantity of Intermediate girders. Cheers.
  10. JAS

    Bottom Plate thickness

    Great ! Thank you so much @JStephen.
  11. JAS

    Bottom Plate thickness

    Dear All, May I know, is there any criteria in API 650, that the thickness of the Bottom plate shall be equal to the thickness of the First Shell course. Also, should the thickness of the Annular plate (if used) shall be equal to the thickness of the Bottom plate. Thank you in advance...
  12. JAS

    Shell wall thickness

    Thank you guys, it is clear that the Thickness are including CA.
  13. JAS

    Shell wall thickness

    Guys, API 650 5.6.1.1 defines the Nominal plate thickness based on the Nominal Tank diameter. May I know whether, the plate thickness mentioned includes the Corrosion Allowance or without Corrosion Allowance? Example, if the selected plate thickness is 6mm (as per 5.6.1.1), should I add...
  14. JAS

    Sheet-to-sheet water assembly

    Hello guys, Iam reviewing an offer just received from a Tank manufacturer for constructing larger Tanks. Manufacturer has mentioned "to build the tank in accordance with the “sheet-to-sheet water assembly” method. He has mentioned that this method affords the advantage of filling gradually the...
  15. JAS

    Transportation of 50m (160') Pressure vessel

    @moltenmetal, This vessel has been designed only as "preliminary". We will place the order to any of the EPC contractors for a detailed design, who inturn will approach any vendors for fabrication. We have approached the logistics person with the preliminary design with all the necessary details...

Part and Inventory Search