Search results for query: *

Hello all; I need your help to simulate the Temperature distribution in wires in contact with molten plastic using ABAQUS + is it a steady state or transient analysis + what type of abaqus elements is recommanded for this kind of analysis (shell, tetra,..) + how can I model the contact between...

Thank you for your reply; Should i define the conductivity with the tie contact? If it's the case wich one must be used (of plastic or of steel)? And how can i define the initial temperature, using a BC or initial condition or it's not necessary to define it?

Hello; Again, thanks a lot for your support! I'm doing a thermal analysis with Abaqus as dicribed below: 1- The initial temperature of the steel is 20°C 2- A molten plastic at 280°C is injected what is the most appropriate modeling method: 1- use a sharing nodes in the interface in this case...

Hello, thanks for your support I still not able to run this analysis with displacement BC instead of force! Ramp amplitude is not supported by abaqus explicit Please who can provide me with an exemple of a working inp for explicit analysis using an imposed displacement BC.

@FEA way: thank you very much for your help! I'm performing the Rotor simulation described above using Abaqus deck of ANSA, then when i checked the model using Abaqus CAE i found that the magnitude value of the rotational velocity in Abaqus CAE is exactly the square root of what i putted in...

Thank you for your support; How can I model with Abaqus the analysis below ( made with Ansys )! i found only that : 1- Bonded contact = Contact Tie

Hello; thanks again for your support! i tried to use a BC displacement in order to move the cube in Z direction but it still not moving until the end of the time step! the same analysis works with a cload force...

Hello All; I'm doing a thermal analysis with Abaqus: 1- 2 parts in contact at room temperature 2- heating one of them to 280° 3- plotting a curve Temperature = function (time) of the 2nd part My questions are: 1- what is the recommended type of mesh element for this kind of analysis (2D or 3D...

@ FEA way thanks again for your Help! is there an equivalent output of SENER which cover the plastic domain too? and what's about PE and PEEQ outputs?

Hello; thanks again for your support! please how can I use one or more of those terms to define the fatigue behavior with abaqus: 1- "strain energy density" 2- "Freudenthal criteria" and if it possible to implement the formula into abaqus or using it with some output : 3- is there a direct...

Hello; Please for the previous Explicit dynamic analysis,i tried to apply a (BC) displacement of 28mm instead of the (cload) force. The part doesn't move until the end of the step! Can we use a displacement BC in explicit dynamic analysis?

@ Fea way: thanks again for your support 1-I will apply the gravity acceleration to all component not on the master node of the rigid body so is it correct thar the reaction force measured at the master node of RB at X direction = force F ? 2-if i'm right, if the gravity load is in Z direction F...

HELLO. the yellow part is in contact pair with the top and bottom parts, and it defined as a rigid body i want to find the "pull out" force F (green arrow) if i apply 5G load (gravity) 1- is it possible to do this simulation with dynamic explicit analysis? 2- what is the right output to find...

@ FEA way [thumbsup2] thank you very much !

ok but what is the default value of the pressure in the contact? i want it to be 20N

thank you for your assistance: - when 2 is moving there is a pressure applied from 1 to 2 in the contact surface so: i want to apply a pressure in the contact (as an input) not to read the pressure in the contact - the simulation finished without problems but the part doesn't move! *i have only...

Hello; - I have two parts (1)&(2) connect by a General contact - initially the component (2) exert a pressure of 20N on the component (1) - I applied a force on (1) my questions are: 1- how to model a pressure of (1) on (2) when (2) is moving? can i consider this pressure on the contact...

i found that the mesh should be more coarser, now, please how can i get the reaction force RF of the sheet metal (yello) i have tried with : *node output, *node print,... but it dosen't work

[thumbsup2] thank you very much it's working now, but i still have Two last questions please. 1- How can i keep the same thickness of the sheet metal in the bending zone (LINE 1 = LINE 2)? 2- how to avoid the deformation of the sheet metal in the contact line with th punch (fig 2)? thanks in...

thank you again for your reactivity, that's exactly, what I did, but I think I didn't choose the right contact here I used a surf to surf general contact so i think when the sheet bends the contact acts to pull the punch with the sheet metal Should i use an edge to edge contact or do you suggest...