Search results for query: *

Does NFPA 85 rule boilers up to 300 HP? Robertp

Thank you all for the clarification, great responses.

ASME Sec II Part A states that the chemical composition of SA/A516 Gr 60 for Mn is 0.79 - 1.30 but a steel manufacturer states their product meets ASME spec but is 0.79 - 1.50 Mn. Does ASME allow a tolerance for exceeding the Product Analysis?

The 70% JE with note: Radiography AS REQURIED is stated in the Design Date block. This is being applied to Quench Duct, Absorption Towers and Incinerator Hot Gas Ducting so I am unclear of the A/R (does it apply or not) when the 70% JE is stated?

AWS and NDT

I am getting differing opinions on several forums as to the extent of RT as it applies to 70% JE. After much feedback I'm leaning to the assumption that butt welds in the circ and longitudinal shell joints of a tank require Spot RT when 70% JE is called out in the Design Data block of the AFC...

I know ASME Sec VIII Div 1 per UW-12 does not require RT for 70% JE on double welded butt joints. Does API 620 per Table 5-2 require RT for 70% JE on double welded butt joints? Thanks in advance for your assistance. qcrobert

Thank you David. Regards Robert

ASME Sec IX PQR was qualified using a 6" pipe in 6 G position thus qualified for welding fillet welds in all positions. Generating additional WPS to provide direction to already qualified welders to weld the tube sheet style part. My question is In section QW-405 on the WPS should the...

Actually the set up of the pipe is similar to what you would see as a tube sheet where the axis of the pipe is horizontal. The end of the pipe to be welded to a tube sheet with the pipe end recessed 1/8" from being flush to the cell plate surface. The travel progression on this corner joint...

What welding position is called when fillet welding downhill a full circle disc on a flat vertical plane (ie wall)?

No it is not stamped by a PE and the Design Data drawing specification block states Specification "Stamping No". Thank you for the clarification about the EOR. As a subcontractor fabricator I was wondering if I need a variance on a requirement in API 620 should I go to the the draftsperson...

In the title block of the tank drawing it states the engineer that: Drawn By: MG Checked By: LPJ Approved By: KPS Which of these persons is considered the EOR? Appreciate your comments, RobertP

The tip on small sample size will be used in the future when qualifying procedures. Re-reading my original post, I found an error and wish to correct it by striking "ERNiCrMo-10" and replacing with "ER2209". Fe% lift off test revealed no ferrite in the weld metal when 2205/C276 was joined with...

I presume that the 2205 was precured with A923 testing. Ordered standard as ASTM G 28-02 (Reapproved 2015) Methods A & B. I would use 30C as a starting point. Unfortunately we do not have the luxury of numerous testing and are limited to testing the two samples at either the higher or lower...

Good information Ed! Yes I have two 1/4"x2"x2" samples ready to send off to the lab for testing to ASTM A 923 Method C. Question is, at what temp do I wish the samples to be subjected to? I've attached the temp chart. Robert

We have qualified WPSs to join 2205 to 2205 with 2209 filler metal and C276 to C276 with ERNiCrMo-10 filler metal. I believe the correct filler metal to join 2205 to C276 is ERNiCrMo-10 filler metal however the 2205/C276 will be subjected to a variety of atmospheric harsh acids and am concerned...

Would like your opinion (or best guess) on what filler metal and welding process you would use to stitch weld a bushing to the flywheel of a motorcycle? Please see attached sketch of crankshaft part assembly and PMI of flywheel and bushing. Thank you your time Robert...

Sorry I meant Engineer of Record

The ERO can grant a variance if you wish to go that route.