Search results for query: *

currently We are using a telemecanie but I am looking for a difernet type that can be rest from the outside of the door.

In are sawmill we have several VFD's with multable motors on them. If one of the curcuit breaker tripss and an electrican has to open the cabinet and reset it. I am looking for a breaker that can be reset from the outside of the door. Does anyone know if there is any reliable units out there...

I am looking into a load monitor, they seem to be what I am looking for but am not fimilar with the brands. Can anyone out there suggest a good, reliable unit that is ethernet ready? Network capable is a must.

250 HP is the motor size. The Motor isn't failing under normal conditions.. The pressure line was the main cause and my boss was looking for better protection....The motor is running as we speak. I am afraid that the normal running amperage will change as the motor gets worn, overheated. .Then...

The blower is for are wood chips. Feed the chips using a chip feeder and the blower produces high volume, low pressure. If you are looking for the manufacture, I would have to get back to you. The real only question I am looking for is how much would the amperage change if the motor is new...

I have a Blower motor that we are having problems with. We monitor the pressure in the pipe going to the cyclone. If the pressure gets to 5 PSI we shutdown the feed, if the pressure gets to 7PSI we shutdown the blower motor. Last week we had a small hole in the pressure line going to the...

Does anyone know the link to more graphics for factory suite ?. I would like to add to my libary. I looked but I don't know the proper name for it...

it isn't for fire control system. The inspector just wants the fans to go off if there is a sigh of fire. Looking into it more Kidde does make a relay that would work good. Thanks for your help ALL

I am required to turn off a fan that feeds fresh air to acouple of rooms. The rooms are finished and surface wiring isn't an option. If I could use the interlok wire that interloks a regular smoke detector together that would be the simplest but was unable to find what signal they us to turn...

Hello All, I need to run a USB port about 100 FT from my PC. Can I make up a cable to convert to RJ 45 and back to USB at my destination?? I see there are cables out there but I would like to learn more about this.If I can do this what is the max distance one can run...

I got a call to a VFD drive not working.I found that the drive had lost it's smoke(burnt up) and a load reactor was also burnt.I tested the motor to ground and everything was good.I wired up a new drive and everything was good.About an hour later I got a call saying that the drive was working...

I am use to using PLC 5 or control logix and I need a one shot instrution in the old slc,it doesn't seem to support it.Is there something in the S2 file I can use?

Sorry ScottyUK I need to have a touch pad to punch a password to access some controls.Are plant is all on control logix 5000 but a old loading chute(Hyd tank and two divertors) are not on a PLC.There is no need for one but they would like to have it password protected, I thought I would wire...

You could turn a relay on with each prox.and have the contacts of the relay in series, that way you would have full Voltage at the end. If you wanted to wire a dummy light in Parrallel with the relay coil and this would give you quick referance to what proxes are not making.

I am looking for a Interface panel. I need to punch in a password and the unit to give me an output.120 VAC would be nice but can be different.All the ones I could find are ether very pricy or are more complex than I require.Thanks

Yes I got it running and it was a node add.Thanks everyone. I posted the pin-out of the AB 1747-CP3 cable.It cost me $16 canadian.Alot cheaper than AB. 1 NC 1 2 3 3 2 4 6 5 5 6 4 7 8 8 7 Both ends are female.

In RS LOGIX I whent to controller properties, controller comm, and I noticed that the comm path is empty.I think this is the problem.If I go to RS WHO and try to apply path it won't take the OK key and I can't seem to get anything in there.

Boy oh Boy I'm close now.I got the pin out, made a cable, created a rs 232 DF1 driver in linx(running)Auto configure was successful.Go into RSLOGIX 500 go to go online and it comes up with a error"the target node is not a SLC-500 or micrologix controller"This is a brand new program I am...

The processor is a SLC 5/03.I now have a PCI card serial port in my pc.Is the cable standard, if not do you know where I can get the pin out.

Nope that didn't work.Please be patient with me ,I find this confusing,Communition has aways been a weak point.At the plant I am at it is mostly set up for us and we take over. I put a serial card in the PC can I use the RS 232 port now? Do I use the RS232 DF! driver in Linx?Is it a standard cable?