Search results for query: *

The Guidance Note GS4(third Edition) This guidance is issued by Health and Safety Executive. Following the guidance is not compulsory and you are free to take other action. But if you do follow the guidance you will normally be doing enough to comply with the law. Health and safety inspectors...

AJerry See this link http://www.hse.gov.uk/research/crr_pdf/1998/crr98168.pdf Its Pressure Test Safety Contract Research Report from HSE Govt of UK. Also get hold of Guidance note GS4 (third edition)...

I liked jmw's idea of a horizontal tow and alternate option of lateral pull on the sub to disturb the sub settlement into the seabed material(unless this makes sub settle more into seabed!!) Was wondering 52' length 8' Dia, 20'WD. Wouldnt it help if only either end was to be lifted up first...

"Depending on the design and operating conditions, there are likely to be areas on an 'expansion loop' which have little movement and low stresses, and may be just as safe to tie in there as at another location. " !! You sure not talking about the loop itself? Or are you really? Siddharth...

greg211 why would you use 31.8 for manifold? I would use 31.3 for wall thickness and SIF's and use PD8010 for stress calculations. Siddharth These are my personal views/opinions and not of my employer's.

Kinsrow You in USA or UK? Siddharth These are my personal views/opinions and not of my employer's.

GregLamberson Big water trunk line was punctured where it passed through slum area and when it burst some casulties happenend, as far as I recall. Its not the Petroleum Pipelines always. Siddharth These are my personal views/opinions and not of my employer's.

"This cases problems when installing valves and tees as it change the orientation" BigInch, Yes meant Swivel flanges. I cant get what exactly S0606 is looking for! Siddharth These are my personal views/opinions and not of my employer's.

Thats why Swivels are used!! Siddharth These are my personal views/opinions and not of my employer's.

JT For a 'pulled bend' you need some straight length at both the ends for the bending machine to get hold of the piece. In general this length is specified as 500mm, I believe. regards Siddharth These are my personal views/opinions and not of my employer's.

odion, Have you discussed this with your senior experienced colleagues? Richard has stated the good direction for your problem. Now its upto you how you go for it. If I were you I would discuss in my work place in the first place. Good luck. Siddharth These are my personal views/opinions...

ek4putr4 Whatever the method you will adopt, we would appreciate if you can come up with the same with the results later. Thanks in advance. Siddharth These are my personal views/opinions and not of my employer's.

4 month on and still 5 months more to go. and this is estimate. At what stage of the design life is the pipeline? As BigInch has said already this is not going to be cost effective anyways. Can the leaking bend be contained by two pigs from either sides? May be using some sort of rubber swell...

Hello all, How about wood? the powdered wood may be split moulded to form a casing around pipe and this may be made rot proof over 20 years or so?? Just a idea. regards Siddharth Siddharth These are my personal views/opinions and not of my employer's.

Leonard, no offense but its no more Bombay, it is Mumbai. regards Siddharth These are my personal views/opinions and not of my employer's.

I believe there is straight 50pence tax out of the 112pence per litre of unleaded petrol (at northern Scotland filling station). In yesterday's Energy article, the author mentioned that the utility bills have gone up by some huge % in the name of helping green agenda, but without reducing a...

http://news.bbc.co.uk/1/hi/world/south_asia/7315308.stm Siddharth These are my personal views/opinions and not of my employer's.

I believe people who boast much about their so called qualifications are trying to hide something in it. Afterall few years experience down the line who cares (with due respect to highly reputed uni's!)which uni you graduated from as the performance speaks for itself. I would never dare imagine...

Gymmeh, In the current economic I would be very cautious to go on such a route. The USA economy is heading towards a recession or at least media says so. In these circumstances what about the income source stability in years to come? The excel budget seems fine for now but the cost of living...

Thank you very much John for the explicit explanation and a star too. I would request you to share some diagram/photograph of such feature, as for me I havent seen anything like this before, rest leave my imagination on its own. regards, Siddharth These are my personal views/opinions and not...