Search results for query: *

go to programs, accessories, communications and you will see hyperterminal. If you need set up info for fanuc let me know. Basically you just have to set up the baud rate and comm's just like anything you would use rs232 to do on fanuc.

any computer now today comes with something called hyperterminal it will comunicate with fanuc controls of any series. works just like procomm

We have a High Frequency Quenching system used to harden rods. We have been blowing transistor in the oscillator cabinet and now we are getting too high of amps on the readouts when we run the machine. Use to run at around 220V at 220amps now its running at 241V at 270 amps. Continues to blow...

as a guess i would say your having some cabling problems some where. Somethings coming loose or loosing connection possibly. or broken wire inside cable. just a thought.

can't answer your question but MrPLC.com had a good article on instruction list for melsec or mits, and also has a forum with alot of guys that could answer your question.

Sent you the info at your email let me know if it works out.

went and looked at abunch of mazak books i got in the basement(used to work shop had all mazaks i keep all the info i aquired) any way everything i read in the book i have for a 640 fusion control points toward no power at lcd, bad cable, bad connections at board or screen or bad monitor.

did some studies at my last job alot of information is on the web and each chuck is different. Find out what type of chuck you have and look up there site or call them. this is the safest and best way to be sure.

alot of the smaller mazaks had a little sub panel box somewere in the general area of the pumps on the back side of the M/C usually in a spot you would never think to look. Double check around your m/c and look for any junction box's large enough to hold a contactor thats probably were you will...

is the screen completely blank? can you home the machine or anything while in the blank screen? You replaced the lcd screen and the powersupply? may have issues somewhere in the cableing or with the windows software. believe there is a way to start the system with out windows but i can't...

Place i work at has OTC Dihan robots Panasonic robots Motoman Fanuc Lincoln. They all have there issues, key like stated before is fixtures, also consider the following: how hard are they to teach and reteach positions this will or may be alot of your downtime. How hard are they to work on for...

snorkes no need to solder these batteries. we have all kinds of old and new mitsubishi plcs at the shop we replace the batteries all the time in them. And we have a direct match up for all batteries. Tomorrow at work i will get you some info. As for replacing batteries the general rules...

not sure i can look in my books on monday and post back late monday night. But there is a quicker way you can call Fanuc at 1-888-fanucusa and ask them and they will tell you..

I don't think i would use it. I saw this on an electrical forum i frequent they may be able to get you what you are looking for not sure of the prices http://www.plastibond.com/ you could also look into what it would cost to have some conduit crome plated if it could be done would last and...

Series 0, T , etc I am looking for something i can print out and keep in my tool box so i don't have to find the book everytime i get an alarm, if we even have the book. any web sites or help

thank you

I just started a new job were we have alot of Mitsubishi PLC's and we use GX developer and GPP software to look at the ladder. My question is i need a list of all the commands or devices for there systems. For example in a ladder you may have K102, M124, etc does anyone have a list of all...

at the shop i work at we moved a bunch of machines last year and this is what we did. Poured new 12" thick floor for all the lathes, mills, and threaders. Poured a 3' deep pad for our grinders and used expansion board to keep it seperate from the 12" floor. I don't know what the...

http://doonan.home.mindspring.com/history.html a little history on this site.

Aaron, try this site you may be able to get a diagram from them, http://www.delcofans.com/index.html