Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: texag
  • Order by date
  1. texag

    QTC and TC - API 6A

    I should refer you both to a previous thread on this topic. There is quite a bit of misinformation and misunderstanding in this current thread. API 6A TC vs. QTC thread330-299646 ~texag
  2. texag

    atomic gas limits in low alloy steels

    metengr, The information in that article is in agreement with other sources I talked to. Thank you for pointing me to it. texag
  3. texag

    atomic gas limits in low alloy steels

    metengr, Thanks for the link, I had seen the keytometals page on hydrogen in steels. My background is engineering for a wellhead equipment manufacturer. Naturally my question relates to hydrogen limits for steels used to make equipment for pumping down and flowing back, a well. Hydrogen...
  4. texag

    API 6A, Material Qualification to Temperature Class X

    KnaT, Have you read API 6A Annex G and API TR 6AF1?
  5. texag

    atomic gas limits in low alloy steels

    Hello, I am looking for information regarding acceptable allowances for hydrogen and nitrogen in low alloy steels such as 41XX, 43XX, or 86XX. There is quite a bit of information on how these atomic gases are introduced during the steelmaking process, and what effects they have on the quality...
  6. texag

    API 6A TC vs. QTC

    salmon2, A sacrificial production part is allowed to be used for extracting a TC but is not allowed for a QTC. A QTC must be extracted from a trepanned core or prolongation removed from the production part. This would appear to be consistent with the elevated quality requirements of PSL2-PSL4...
  7. texag

    Api 6a Trim Material

    Given the termperature you listed, the valve would fall into the "Y" temperature class of API 6A, which is 0F-650F. I am not too familiar with geothermal wells but aren't those closed loop systems where you are simply exchanging heat with the large heat sink that is earth? Therefore, you...
  8. texag

    API RP 7G calcs - Mathcad

    You make good points, and sorry if I offended, it sounds like you have served committee time. Complaining and not being part of the solution, not very proactive of me. Again, thanks for the help. texag
  9. texag

    Api 6a Trim Material

    yalkamer API 6A material classes are broken up in to two basic groups; general service and sour service. A sour service environment contains H2S. The 6A specification defers further definition of sour service to NACE MR0175. Do you have exposure to H2S or will there be free Hydrogen?
  10. texag

    API RP 7G calcs - Mathcad

    redpicker, I knew that is what those factors were for but am still dumbfounded as to why API doesn't simply explain that. I completely re-wrote those equations in terms of the taper angle and am getting the same values (with units!) as you would get just using a calculator. I am satisfied...
  11. texag

    API RP 7G calcs - Mathcad

    I have been trying to create a Mathcad worksheet using the formulas provided in this recommended practice, namely those formulas in Appendix A.8. As with most API specifications, the formulas do not lend themselves to use in Mathcad if you wish to use a unit system. If you attempt this, and I...
  12. texag

    AISI 1141 for driveline application

    I am looking at using AISI 1050 annealed for this component. The 10XX series steels are readily available and inexpensive due to lack of high cost alloying elements such as Ni, Cr, and Mo. The higher carbon content allows me to get the required mechanical properties in either the annealed or...
  13. texag

    Applying a pure tensile load from a strap or rope sling

    Your question is inclear. What are you trying to apply a load to? It sounds like you are trying to analyze the resultant forces on the belt mountings caused by the occupant being restrained. A FBD would help if you could sketch and attach, you may even answer your own question by doing so. texag
  14. texag

    Cosmos Newbie

    I would drop the wire model and analyze a flat plate analog that has the same mechanical responses as the trays. As long as the stiffness and Poisson's ratio are the same as the real thing you should get fairly accurate results, worth a shot anyway. Compare the yield to the min yield of the...
  15. texag

    AISI 1141 for driveline application

    CoryPad, The loading is primarily torque (torsion), 0-2100RPM, and light to moderate shock loads. Assuming the sulfide stringers are oriented along the axis of the bar a torsion application would be loading perpendicular to those inclusions and thus not recommended based on fatigue failure...
  16. texag

    Thickness of Blind plate for Hydrotest

    kvbalu, You could refer to Roarks's for flat plates, table 24 case 10b, to size your end cap. As MJCronin mentioned, that likely will be a significant thickness. texag
  17. texag

    AISI 1141 for driveline application

    swall, Hypothetically this part would start as annealed or normalized barstock. The companion flange would have a circular bolt pattern on one end to connect to the driveshaft and an internal spline for connecting to a gear. They are rather bell shaped if you are familiar with common...
  18. texag

    AISI 1141 for driveline application

    Recently I discovered that a large manufacturer of commercial and industrial driveline components machines companion flanges out of AISI 1141 resulfurized steel. The part in question is something we would like to manufacture in house but I have doubts about using the same material based on the...
  19. texag

    NORSOK R-001, Nozzle Loads

    narenr, A picture says a thousand words right? Thank you!
  20. texag

    NORSOK R-001, Nozzle Loads

    To start my analysis I applied the internal pressure and the loads created by the internal pressure. At the end of the nozzle I simulated remote loads to create the two momemts and the force as described in NORSOK, well, my interpretation anyway. I attached a sketch of this in a previous post...

Part and Inventory Search

Back
Top