Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. tarzan56007

    High Leg on Delta-Delta Transformer causing problems

    I think some more meter readings are in order here, are you saying that the voltage from phase B to nuetral is only 240 when that one machine is running, or is it all the time, if you can go into this facility when machines are offline and check voltages, and if you have normal voltage readings...
  2. tarzan56007

    Demand Load calculation

    Peepee please explain the science you used to determine that the Union in Chicago controls the areas electrical codes, I would think that the Chicago Inspection Department as well as the IBEW should take offense to that statement. I know that I personally do. P.T. Local #343, Minnesota.
  3. tarzan56007

    NEMA rating standard is 460V but not 480V, why?

    voltage specs are considered to be nominal, 440, 460, and 480 for example are all considered the same for all practicle purpose, The actual voltage at which a circuit operates can vary from the nominal within a range that permits satisfactory operation of equipment.
  4. tarzan56007

    Help 1HP Electric Motor

    is this setup on a bridge crane or similar and controls from pendant or is the winch stationary and operator station permanently mounted, if you want to do this from a pendant control then you will probably need to use a relay system but if it is a stationary set up then you need a drum switch...
  5. tarzan56007

    Single Phase Bridgeport

    just noticed this post now, probably a little late, I would think a VFD rated for twice the three phase horse power rating for your motor would be your best bet, you will have speed control, reverse, ramp up and braking properties if needed as well as motor overload protection all in one, these...
  6. tarzan56007

    Cincinnati Press Brake FormMaster 2

    is there any chance that the steel itself could have inconsistant measurements, thickness or length.
  7. tarzan56007

    Pedestrian warning light when towmotor is near.

    a loop detector imbeded in the concrete is what you are looking for, I have installed several of these but was only an employee so am not sure of who venders may be but I would try local overhead door companies for the loop materials, they use these to activate the door openers when forklifts...
  8. tarzan56007

    rotary phase converter, vfd, inverter

    This has all been very informative for me and I appreciate everyones opinion, I will build the rotory unit for now because I already have all the parts but in the future I will probably use a vfd for each application, thanks Tarzan.
  9. tarzan56007

    rotary phase converter, vfd, inverter

    I knew that VFDs could be used to provide three phase power to the smaller motors but was unaware that it was fesable for 10 hp motors, that is a good idea, but I guess the main reason for using a rotary converter is money, I will only have around $300 plus a day or two work into my rotary...
  10. tarzan56007

    AFCIs and GFCIs

    Just wondering if anyone has any experience with using both a ground fault recepticle in line with a arc fault recepticle, is it better to have one in front of the other? will one nuisence trip the other?
  11. tarzan56007

    Small Generation

    P.S. to tulum, I am sure you probably are regretting this post at times since it does stir up a lot of contraversy, I believe if you could design a small system possibly using an induction type generator and divert a small amount of the water without disturbing the natural flow of things you...
  12. tarzan56007

    Small Generation

    regardless of everyones opinion on wether or not hydro electric systems are more or less benificial to the enviroment it still needs to be submitted to your local department of natural resources or whatever governing agency in your area handles such matters, these installations do alter the...
  13. tarzan56007

    Reversing Compound DC Motor

    I can think of a couple of ways to do this, personally I would use a double pole-double throw-center off dc motor rated toggle switch, connect A1 and A2 to the two common terminals then connect F1 to one of the remaining terminals and take a jumper wire from there to the terminal located...
  14. tarzan56007

    Voltage drop calculations

    For voltage drop calculations the NEC or NFPA 70 is not concerned with insulation type or thickness, if you refer to chapter nine, table eight in the back of 2002 NEC it will list conductor properties for voltage drop calculations and ohms per one thousand feet of resistance for each conductor...
  15. tarzan56007

    why did my motor contactor burn up

    Just a thought but from a maintenance mans perspective you may have two problems, one as most agree would be a control circuit problem but the fact that one of the main contacts burned up would seem to me a possible loose connection anywhere from the bottom to the starter to the motor windings...
  16. tarzan56007

    rotary phase converter, vfd, inverter

    The service on my shop is 200 amp 230 volt single phase 60 htz and the only reason I am building the rotary phase converter as 15 or 20 hp is because I have a couple of these motors on hand, the most these motors will ever start is 5 hp and the most they will ever run is probably 7 to 9 hp max...
  17. tarzan56007

    Which Motor ... - Redux

    Do you think it is possible that the conveyor or whatever system that is feeding this unit with media is undersized, possible if rocks were fed into this machine a little quicker it would work harder and therefore more efficiently, another thought is it may be designed for zero down time so as...
  18. tarzan56007

    propane line in MCC

    dpc is right about the dedicated space but the NEC also addresses working space in front, sides, and back of electrical apparatus that have access panels that are removable for working on that equipment, the best bet is to contact the local electrical inspector, or at least a licensed...
  19. tarzan56007

    rotary phase converter, vfd, inverter

    the phase converter is intended to run several smaller motors in the shop and the vfd would be connected to only one of them at this time, mostly for speed control, just wondering if it would also help on the voltage, amperage and phase angle qualities going into that machine. Tarzan.
  20. tarzan56007

    rotary phase converter, vfd, inverter

    I am planning to build a rotary phase converter for my shop probably going to use a 15 or 20 hp baldor motor, most info I have read refers to balancing problems between phases, wondering if a vfd connected between the phase converter and the machinery would do any good with controlling...

Part and Inventory Search

Back
Top