Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Metalsmythe1977

    BACB30FM Test Report "Too Short"

    Wil, I spoke with the manufacturing company engineer about this and he said that the "too short" entry was due to the fact that the pin grip length(.375") is below 2X the diameter(.500"). He cited Procurment Specs BPS-F-67 REV AL and HS342 REV AG (which are referenced on the Test Report)and...
  2. Metalsmythe1977

    BACB30FM Test Report "Too Short"

    Thanks Gents; I plan to call the manufacturer and ask the same question. I suspect "too short" means that the fasteners would not fit into their test apparatus. Respectfully, Metalsmythe77
  3. Metalsmythe1977

    BACB30FM Test Report "Too Short"

    I'm looking at a Quality Assurance And Reliability Test Report for a batch of BACB30FM8-6 pins we recieved and under the "Ultimate Tensile Strength/Pounds" column the entry reads "too short". The same entry was made in the "Tension/Tension Fatigue Life/Cycles" column. Any concerns I should be...
  4. Metalsmythe1977

    E-Drill usage on composite panel fasteners

    Does anyone have experience or feedback on the use of "E-Drill" to remove blind fasteners on composite structure? The system uses a precision EDM electrode with a built-in water flushing system to prevent heat damage. The EDM cuts the fastener head enought to allow for easy shank removal...
  5. Metalsmythe1977

    Taper-Lok fatener group numbers

    There are actually six groups (1-6) for each fastener series and they overlap as the overall fastener length grows: TL100 Nominal(Group 1,2,3), TL110 1st oversize(Group 2,3 4), TL130 2nd oversize (Group 3,4,5), and TL140 3rd oversize (Group 4,5,6). The cycle repeats at the next nominal size...
  6. Metalsmythe1977

    Brush Plating Standard for 17-4PH Repair Bushings

    Thank you very much wktaylor. We're working with a vendor on this to potentially purchase the equipment. Respectfully, ms1977
  7. Metalsmythe1977

    Brush Plating Standard for 17-4PH Repair Bushings

    Does anyone know the recommended standard for brush plating cadmium on 17-4PH repair bushings?
  8. Metalsmythe1977

    Spec sheet for TL200 fastenrs

    WKtaylor We purchased one from Amazon about 5 years ago; it is indeed very fat and has been taped up several times. Sorry to hear your copies have been hijacked so many times. The blue book sounds interesting... Regarding TLs the USAF recently tightened up the installation process to ensure a...
  9. Metalsmythe1977

    Spec sheet for TL200 fastenrs

    McMoose You might try to get a copy of VOI-SHAN AEROSPACE FASTENER DESIGN MANUAL (orange cover) it's out of print but a used copy may be on Amazon or similar web site. C-130 aircraft still have them by the dozens... Respectfully metalsmythe77
  10. Metalsmythe1977

    Rivet Symbol Legend on older engineering drawings

    Thanks Mr Taylor. See attachment.http://files.engineering.com/getfile.aspx?folder=3e7ca4bb-988c-4e45-8721-355e14e666e2&file=rivet_symbol_legend.pdf
  11. Metalsmythe1977

    Rivet Symbol Legend on older engineering drawings

    Does anyone know the history/background on legacy aircraft drawings that have a "Rivet Symbol Legend" block on the upper right corner of the drawing title page? They show a basic circle, basic circle with a diagonal, etc. depending on the solid rivet head style and diameter. Was there a code...
  12. Metalsmythe1977

    Classification of minor & major repair

    I use an SRM for a military aircraft that classifies a major repair as: "A repair that involves restoring two or more primary structural members to original loadcarrying requirements and/or aerodynamic characteristics is considered a major repair."
  13. Metalsmythe1977

    MS20470 Raised Head Rivet Allowable Head Damage

    Does anyone know of some good references for raised head rivet (installed) inspection criteria? I have an aircraft with numerous MS20470AD4/5 rivets that have mechanical damage to the raised heads from a power tool. Some damage is very minor; while some are almost flat to flush with the...
  14. Metalsmythe1977

    Defective Standard Hardware - MS21042, NAS1291 self-locking nut failures

    Has anyone been up to speed on the defective MS21042/NAS1291 self-locking nuts being reported due to improper cad coating processes? Any wisdom from the Forum would be appreciated.
  15. Metalsmythe1977

    First Oversize for a MS21250 Bolt

    Not aware of any. There is a similar 12-point tension head bolt: MBT50 that may be available in X or Y oversize configuration. We have had trouble finding these as well (very expensive with outrageous lead time.)
  16. Metalsmythe1977

    1.15 Fitting Factor

    Can someone summarize in laymans terms the application of 1.15 "fitting factor" in aircraft joint analysis? Thanks!

Part and Inventory Search

Back
Top