Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations cowski on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Kawartha

    How to balance a pump impeller?

    siamterm, Balancing the rotating parts of a pump is dependant on the type of pump. For example: Many ANSI (Typical Chemical Processing Pumps)are single plane balanced (also known as static balance). This can be done by placing the impeller on a shaft and mounting this between two free...
  2. Kawartha

    Well Pump Problem

    Islandeng, Hi also to PUMPDESIGNER and D23. Sorry if I offend anyone with the following comments, I haven't had time to review all of the comments. I think Coastpumpguy has come to the same kind of conclusion that I have. Several years ago, many of the couplings for submersible pumps were...
  3. Kawartha

    Seawater Pump

    Hi PUMPDESIGNER, It's been some time since I've looked at Eng-Tips, and who do I find in the center of an interesting topic but PUMPDESIGNER. This is an area that I spent a good deal of time with over the last few decades. I think that many have already indicated that this would probably be a...
  4. Kawartha

    ACTUAL TDH NOT MATCHING PUMP CURVE

    TechSupport1, I don't think that you have described your system in detail. What you are observing makes me think that you may have air (or some type of compressible gas) which is entrained in the liquid entering the pump. When flow is reduced to shut-off, possibly the air is escaping prior to...
  5. Kawartha

    Barske Impeller

    Robjack, As stated above the Barske (also written as Barski)impeller is one of the two keys to low flow / high head pump design. The other important ingredient is a concentric casing (rather than eccentric with a cutwater). This allows liquid to stay in the casing for more than one revolution...
  6. Kawartha

    Low flow / high head requirements

    joisy, Another alternative centrifugal type is the Rotary Pitot Tube type which is manufactured by Roto-Jet, which I think is owned by Weir Pumps now. Richard
  7. Kawartha

    amp readings?

    Thanks PUMPDESIGNER, it obviously needed repeating. Have not heard from you recently. How's business. Regards, Richard
  8. Kawartha

    amp readings?

    Arisi, I agree with all of the above comments by Artisi, rmw and JohnGP. I think that the easiest way for you to check the pump performance is to obtain a copy of the manufacturers Head-Capacity-Efficiency-BHP curve. This will confirm for you whether the BHP in fact does drop as the flow...
  9. Kawartha

    pump curves

    Could you also provide the total differential head (this will also be shown on the nameplate), and the current (and voltage) that the motor is drawing. Are you aware that Dresser is now part of FLOWSERVE. I would be very surprised if they can not provide this information. As a last resort you...
  10. Kawartha

    DIAGNOSE THIS

    PUMPDESIGNER, I'm having some problem understanding your explanation for this damage. I guess BobPE is also. I think what you are saying is that the chemical attack occured because of the high velocity, and only in specific areas. Are you making a comparison to erosion-corrosion, where the...
  11. Kawartha

    DIAGNOSE THIS

    PUMPDESIGNER Is the pump discharging into a common header along with other pumps? Please describe the pump: vertical sump type, end suction, waste water??
  12. Kawartha

    DIAGNOSE THIS

    Richard, I think hydrae may be on the right track. Was the suction located in a sand bar or sandy beach? Can't explain the casing being in good condition. One would expect some erosion there as well. What type of casing - volute or diffuser? Richard
  13. Kawartha

    DIAGNOSE THIS

    PUMPDESIGNER, Please advise the impeller material, casing material, etc. Was erosion observed in the casing as well? Richard
  14. Kawartha

    DIAGNOSE THIS

    PUMPDESIGNER, Don't give it away too quickly. Give us all time to think about it. I guess your back. Richard
  15. Kawartha

    Pump Alignment

    dross56, If you are talking about the pump suction and discharge flanges, the answer is yes. Any significant out of alignment between the pump and piping flanges will be reflected in misalignment of the shaft. The greater the flange loads, the more misalignment. API 610 provides allowable...
  16. Kawartha

    high motor load

    upm, From the information that you have provided, we can not determine if the problem is the pump or the motor. If you remove the high amp motor (from pump 1) and couple it to the other pump (pump 2), if it continues to draw high amps at shut-off, you will know the motor (from pump 1) is not...
  17. Kawartha

    reservoir and tank in series

    lilliput1, Just a couple of other points that I'd like to make. 1) When the pump is not operating, it would be necessary to have the pump discharge valve or reservoir valve closed to prevent pump rotation. Although pump rotation would be in the normal operating direction, pump speed could...
  18. Kawartha

    reservoir and tank in series

    lilliput1, You are right about the pump acting as a turbine, but only on the condition that it is not operating and that the piping between the reservoir and pump and pump to discharge are sufficiently open. However, when the pump is started (this should be done only against shut-off head, and...
  19. Kawartha

    Pump Alignment

    dross56, It is always helpful to know as much as possible about the various aspects of pump installation. However, as MortenA suggested, always refer to the pump manufacturers "Installation, Operation and Maintenance" (IOM) Manual. This document is specific to your pump and should...
  20. Kawartha

    V-Belt drive selection question

    Lovison, As I recall good belt drive design does not allow ratios above 4:1. You may want check this out with one of the belt/pulley suppliers.

Part and Inventory Search

Back
Top