Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. fernandoelec

    Motor Differential CTs

    Do you want protect the motor against internal faul or only measuremet? If you want the diferential protection, the best is the use of 6 CTs Fernandoelec
  2. fernandoelec

    RSM gearmotor speed control

    with the same configuration you can purchase a VFD from Invertek(UK) they have single phase VFD with the features that you need Fernandoelec
  3. fernandoelec

    325 MVA with 2% Flicker

    An additional comment to the Skogsgurra´s info, you must be care with the power spikes, cause in some cases with the load attached to the motor shaft an over voltage can be present in the AC drive's DC Bus and it can explode, please ensure that the AC drive has a DC Braking resistor unit this...
  4. fernandoelec

    VFD Power Modeling

    Recheck if your VFD has the PID function or if you can control it by a torque adjusment fucntion inside. Other option is that you can use the the analog output signal configured as a Power or energy signals and with a small PID controller feedbak the analog VFD's speed input Fernandoelec
  5. fernandoelec

    Level Sensor for Equipment Protection

    Hi Sfardella, It depend of your pplication, but if is critically for your equipment, I suggest to you a presure sensor, I have used in appli cations with slurry and hard enviroments, if you have a fluid mixed this is a good option, for example you can use foxboro, ABB or Rosemount devices for...
  6. fernandoelec

    How to interface RS-485 / Modbus protocol

    you can find that information in the following address: www.modbus.org I hope that this thing can help you.Let me to know if this is right. Fernando Sánchez
  7. fernandoelec

    interface RS-232 / Jbus protocol

    jsrinivasu, In the following address you can to find all the information about the Modbus protocol: http://www.modbus.org/default.htm In the section Modbus serial line, in the category column, you must to choose "implementation guide", there you'll find a file calling...
  8. fernandoelec

    interface RS-232 / Jbus protocol

    jsrinivasu, In this address you can find all that your need about of Modbus protocol: http://www.modicon.com/techpubs/toc7.html Fernandop Sánchez
  9. fernandoelec

    interface RS-232 / Jbus protocol

    jsrinivasu, In addition to Macbeth info, you must to have the Mapping register of the device, cause when you´ll obtain communication you have to test the info. If you don´t know how to do the cable, let me to know, to give you some addresses where explain step by step the Job. If you can´t...
  10. fernandoelec

    Radio Frequency Data Management

    Hi, You give the properties only to the Mscomm control, rightnow you have to program the event Oncomm of that control, using select case with the variable commevent and in the case use number 2, use the Input property to capture the info, once do it, you must to store the data in a variable...
  11. fernandoelec

    HOW TO TEST AND MEASURE AN IGBT

    shenyee, What do you exactly need? I don´t have read yet "Magic Sinewaves" , but tell me your specific question. Fernando Sánchez
  12. fernandoelec

    HOW TO TEST AND MEASURE AN IGBT

    Hi friends, thanks a lot for your help (dydt,jbartos,electricpete,cbarn24050,tmahan), i found a test and measure procedure of IGBTS FUJI in the follow address: www.fujisemiconductor.com/pdf/app_notes/reh982.pdf , in the appnotes section, it correspond to an IGBT instruction manual where it...
  13. fernandoelec

    HOW TO TEST AND MEASURE AN IGBT

    Thanks to dydt and jbartos for your help, but I have a 1336 plus Allen Bradley AC drive, the dc bus fuse open and it trip by low DC bus level, it working with fuji IGBT, most exactly with the refference 2MBI300N-120, I want to test the IGBTs to determiente if any of them are failed, i tried to...
  14. fernandoelec

    HOW TO TEST AND MEASURE AN IGBT

    Please help me some one that knows how to measure an IGBT and how to test it. I´ll appreciate your help
  15. fernandoelec

    How to test an IGBT??

    Hi, my friends Some body knows how to test the IGBT's, more exactly Fuji Device can test it, or what is the circuit easiest to do it?? I'll appreciate your help. Fernando Sánchez

Part and Inventory Search

Back
Top